P6 G&G ARP556 series custom AEG

P6-AEG-ARP556

New product

Build time 3 - 6 days

Moyenne des votes pour ce produit
5.0 / 5
Moyenne : 5.0 / 5
Basée sur 3 avis clients.

Configure

Si vous souhaitez enregistrer votre configuration, vous devez d'abord vous connecter.

Connexion

Customize your product

Choose your replica version.

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • G&G ARP556 AEG

              Features:

    • CQB M4 style rifle AEG.
    • Extremely compact and lightweight.
    • Based off of the G&G CM16 series.
    • 5.56 style carbine.
    • Fully automatic / semi-automatic select fire with 450 rd high capacity magazine.
    • Inline MOSFET.

      Specifications:

      Length - 500mm
      Weight - 2350g
      Inner Barrel Length - 128mm
      Magazine Capacity - 450 Rounds
      Gearbox - Ver 2 Full Metal
      Thread Direction - 14mm CCW
      Blowback - None
      Magazine Compatibility - Ships with its own G&G magazine.

    G&G ARP556 AEG

  • G&G ARP556 Battleship Grey

              Features:

    • CQB M4 style rifle AEG.
    • Extremely compact and lightweight.
    • Based off of the G&G CM16 series.
    • 5.56 style carbine.
    • Fully automatic / semi-automatic select fire with 450 rd high capacity magazine.
    • Inline MOSFET.

      Specifications:

      Length - 500mm
      Weight - 2350g
      Inner Barrel Length - 128mm
      Magazine Capacity - 450 Rounds
      Gearbox - Ver 2 Full Metal
      Thread Direction - 14mm CCW
      Blowback - None
      Magazine Compatibility - Ships with its own G&G magazine.

    G&G ARP556 Battleship Grey

  • G&G ARP556 V2S

              Features:

    • CQB M4 style rifle AEG
    • Polymer Body
    • Extremely compact and lightweight.
    • Based off of the G&G CM16 series.
    • 5.56 style carbine.
    • Fully automatic / semi-automatic select fire with 450 rd high capacity magazine.
    • Inline MOSFET.
    G&G ARP556 V2S

Choose your output power, value in FPS with 0.20gr BBs. Please note : FPS may vary, we cannot garantee exact FPS asked, it will be a range. For low power configuration please note that the cylinder can be modified.

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • 270 FPS

    270 FPS

  • 280 FPS

    280 FPS

  • 290 FPS

    290 FPS

  • 300 FPS

    300 FPS

  • 310 FPS

    310 FPS

  • 320 FPS

    320 FPS

  • 330 FPS

    330 FPS

  • 340 FPS

    340 FPS

  • 350 FPS

    350 FPS

  • 360 FPS

    360 FPS

  • 370 FPS

    370 FPS

  • 380 FPS

    380 FPS

  • 390 FPS

    390 FPS

  • 400 FPS

    400 FPS

  • 410 FPS

    410 FPS

  • 420 FPS

    420 FPS

  • 430 FPS

    430 FPS

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • SAFE - SEMI - AUTO

    SAFE - SEMI - AUTO

  • SAFE - SEMI - BURST3

    SAFE - SEMI - BURST3

  • SAFE - SEMI ONLY

    SAFE - SEMI ONLY

Choose Your piston. Basically, we advise you to choose the Balystik which is very versatile and resistant, but you can choose another model ! We make AOE modification of the piston + piston head whatever the model chosen in order to allow a perfect start of the cycle between the sector gear and the first piston teeth.

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • Lightweight 14 teeth Piston

    • Essential part for upgrading your Airsoft AEG
    • Polymer Construction Lightweight piston with high impact-durability
    • 14 Full Teeth rack gear made of metal
    • Suitable for mainstream high-speed tune-up and has excellent operational characteristics
    • The Grease grooves cut on the rail-guides keep it lubricated
    • Suitable for standard AEG gearbox Tokyo Marui and clones
    Lightweight 14 teeth Piston

  • Balystik polycarbonate 14 steel teeth piston for AEG

    • Balystik polycarbonate 14 teeth steel piston
    • Extremely durable body made of polycarbonate
    • 14 Full Teeth rack gear made of metal
    • 16gr only
    • Suitable for all configuration from high speed to high torque
    • Suitable for standard AEG gearbox Tokyo Marui and clones
    Balystik polycarbonate 14 steel teeth piston for AEG

  • Balystik ULTRALIGHT 14 steel teeth piston for AEG

    • Balystik ULTRALIGHT 14 teeth steel piston
    • Ultralightweight "cheese edition" with 7 openings
    • Extremely durable reinforced POM construction
    • 14 Full Teeth rack gear made of metal
    • 13,3gr only
    • Suitable for high speed and semi automatic shooting with high rate trigger response
    • Suitable for standard AEG gearbox Tokyo Marui and clones
    Balystik ULTRALIGHT 14 steel teeth piston for AEG

  • POINT POLICARBON PISTON WITH 14 STEEL TEETH

    POINT POLICARBON PISTON WITH 14 STEEL TEETH

  • FPS Softair Full Metal Teeth light Piston

    FPS is proud to present the first lightened piston with 100% Made in Italy technopolymer body and all metal teeth.

    For the material of the piston the POM C was chosen, a technopolymer with high mechanical performances and a very low friction coefficient because it is self lubricating. The rack has been manufactured using MIM (Metal Injection Molding) technology, because this production process guarantees dimensional precision and strength equal to those of solid machining. The rack is presented with the second missing tooth and with the third already lowered by 3 tenths of a millimeter because this configuration predisposes the piston itself for a correct angle of engagement (AOE) and makes it suitable for high speed. The type of metal injected is SAE 4650 which is currently considered the best material on the market for this type of use. The sliding guides are designed to minimize friction and retain the lubricant for a long period of time. The rack seat is decentralized to favor the coupling between the piston teeth and those of the sector gear. The longitudinal reinforcements at the sides of the teeth increase the robustness of the piston and avoid contact of the rack with the inner wall of the cylinder. Special ribs decrease the contact surface between the spring and the internal part of the piston body and consequently also the friction between metal and technopolymer is decreased during contraction and elongation due to the firing cycle.

    100% MADE IN ITALY
    100% COMPATIBLE MARUI

    FPS Softair Full Metal Teeth light Piston

  • FPS Softair Full Metal Teeth Piston

    FPS is proud to present the first piston with 100% Made in Italy technopolymer body and all metal teeth.

    For the material of the piston the POM C was chosen, a technopolymer with high mechanical performances and a very low friction coefficient because it is self lubricating. The rack has been manufactured using MIM (Metal Injection Molding) technology, because this production process guarantees dimensional precision and strength equal to those of solid machining. The rack is presented with the second missing tooth and with the third already lowered by 3 tenths of a millimeter because this configuration predisposes the piston itself for a correct angle of engagement (AOE) and makes it suitable for high speed. The type of metal injected is SAE 4650 which is currently considered the best material on the market for this type of use. The sliding guides are designed to minimize friction and retain the lubricant for a long period of time. The rack seat is decentralized to favor the coupling between the piston teeth and those of the sector gear. The longitudinal reinforcements at the sides of the teeth increase the robustness of the piston and avoid contact of the rack with the inner wall of the cylinder. Special ribs decrease the contact surface between the spring and the internal part of the piston body and consequently also the friction between metal and technopolymer is decreased during contraction and elongation due to the firing cycle.

    100% MADE IN ITALY
    100% COMPATIBLE MARUI

    FPS Softair Full Metal Teeth Piston

  • FPS Softair ZERO-SHOCK Lightened 14 Teeth Piston

    FPS is proud to present the first ZERO-SHOCK lightened piston with 100% Made in Italy technopolymer body and full metal teeth. This system patented by Fps allows to attenuate the stresses that the rack transmits to the piston body and it makes the assembly enormously more resistant and reliable than a normal piston.

    For the material of the piston was chosen a reinforced technopolymer with added elastomer with high mechanical performances and a very low friction coefficient. The rack has been manufactured using MIM (Metal Injection Molding) technology because this production process guarantees dimensional precision and strength equal to those of solid machining. The rack is presented with the second missing tooth and with the third already lowered by 3 tenths of a millimeter because this configuration predisposes the piston itself for a correct angle of engagement (AOE) and makes it suitable for high speed.


    The type of metal injected is SAE 4650 + HRC38-42 hardening treatment which is currently considered the best material on the market for this type of use. The sliding guides are designed to minimize friction and retain the lubricant for a long period of time. The rack seat is decentralized to favor the coupling between the piston teeth and those of the sector gear. The longitudinal reinforcements at the sides of the teeth increase the robustness of the piston and avoid contact of the rack with the inner wall of the cylinder.

    Special ribs decrease the contact surface between the spring and the internal part of the piston body and consequently also the friction between metal and technopolymer is decreased during contraction and elongation due to the firing cycle.

    100% MADE IN ITALY
    100% COMPATIBLE MARUI

    FPS Softair ZERO-SHOCK Lightened 14 Teeth Piston

  • FPS Softair ZERO-SHOCK 14 Teeth Piston

    FPS is proud to present the first ZERO-SHOCK piston with 100% Made in Italy technopolymer body and full metal teeth. This system patented by Fps allows to attenuate the stresses that the rack transmits to the piston body and it makes the assembly enormously more resistant and reliable than a normal piston.

    For the material of the piston was chosen a reinforced technopolymer with added elastomer with high mechanical performances and a very low friction coefficient. The rack has been manufactured using MIM (Metal Injection Molding) technology because this production process guarantees dimensional precision and strength equal to those of solid machining. The rack is presented with the second missing tooth and with the third already lowered by 3 tenths of a millimeter because this configuration predisposes the piston itself for a correct angle of engagement (AOE) and makes it suitable for high speed.


    The type of metal injected is SAE 4650 + HRC38-42 hardening treatment which is currently considered the best material on the market for this type of use. The sliding guides are designed to minimize friction and retain the lubricant for a long period of time. The rack seat is decentralized to favor the coupling between the piston teeth and those of the sector gear. The longitudinal reinforcements at the sides of the teeth increase the robustness of the piston and avoid contact of the rack with the inner wall of the cylinder.

    Special ribs decrease the contact surface between the spring and the internal part of the piston body and consequently also the friction between metal and technopolymer is decreased during contraction and elongation due to the firing cycle.

    100% MADE IN ITALY
    100% COMPATIBLE MARUI

    FPS Softair ZERO-SHOCK 14 Teeth Piston

Choose your piston head. Basically, we advise you to choose the Balystik CNC aluminum bearing Piston head model which is very versatile and resistant, but you can choose another model ! We make AOE modification of the piston + piston head whatever the model chosen in order to allow a perfect start of the cycle between the sector gear and the first piston teeth.

  • Balystik CNC aluminum bearing Piston head

    This piston head has 8 ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. Each piston head is made of CNC aluminium and it is also anodized for smooth surface finish. This is the most advanced version with 11.8gr only, 8 ventilation holes for higher speed and rate of fire, ball-bearing and excellent seal.

    • Essential part for upgrading your Airsoft AEG
    • Made of CNC aluminum with hard anodize
    • Ball bearing system help reduce spring torsion
    • 8 Holes ventilation
    • 11.8gr only
    • Suitable for all configurations from high-speed to high torque set-ups
    • Suitable for standard AEG gearbox Tokyo Marui and clones
    Balystik CNC aluminum bearing Piston head

  • SHS Aluminum ventilated piston head 6 holes - red

    Piston head HI-FLOW mounted with a bearing. The piston head has 6 holes allowing perfect replica cycle and a optimal compression of the seal rubber in the cylinder.

    SHS Aluminum ventilated piston head 6 holes - red

  • SHS Aluminum ventilated piston head 8 holes - blue

    Piston head HI-FLOW mounted with a bearing. The piston head has 8 holes allowing perfect replica cycle and a optimal compression of the seal rubber in the cylinder.
    SHS Aluminum ventilated piston head 8 holes - blue

  • SHS Aluminum ventilated piston head 8 holes - red

    Piston head HI-FLOW mounted with a bearing. The piston head has 8 holes allowing perfect replica cycle and a optimal compression of the seal rubber in the cylinder.
    SHS Aluminum ventilated piston head 8 holes - red

  • FPS Softair POM piston head for high rof and silence (TPAVP)

    POM piston head designed for high rof and to increase the silence of the replica thanks to the very small knocking surface (TPAVP). It is the lightest among those produced by the FPS for rifles with gusts over 30 BBs / second. Its adoption lightens the weight of the piston and piston head with a significant reduction in mechanical stress and noise. The particular conformation of the striking part (conical degrading towards the center) ensures that the ventilation holes are never closed by the rubber of the cylinder head, without however leaving too much air between the cylinder head and piston head. All this ensures a perfect anti-vacuum system without ever producing power losses. For preparations of replicas with extreme rates our technical team recommends the use of the washer to lighten the beating mass.

    100% COMPATIBLE MARUI
    100% MADE IN ITALY

    FPS Softair POM piston head for high rof and silence (TPAVP)

  • FPS Softair POM piston head for high rof and silence (XPAVP)

    POM piston head designed for high rof and to increase the silence of the replica thanks to the very small knocking surface (XPAVP). It is the lightest among those produced by the FPS for rifles with gusts over 30 BBs / second. Its adoption lightens the weight of the piston and piston head with a significant reduction in mechanical stress and noise. The particular conformation of the striking part (conical degrading towards the center) ensures that the ventilation holes are never closed by the rubber of the cylinder head, without however leaving too much air between the cylinder head and piston head. All this ensures a perfect anti-vacuum system without ever producing power losses. For preparations of replicas with extreme rates our technical team recommends the use of the washer to lighten the beating mass.

    Technical specifications:

    Weight: 5.56 grams (with technopolymer washer)

    100% COMPATIBLE MARUI
    100% MADE IN ITALY

    FPS Softair POM piston head for high rof and silence (XPAVP)

  • FPS Softair double o-ring ball bearing AEG Piston Head

    FPS CNC ERGAL Double O-Ring Ball Bearing AEG Piston Head (TPGE).

    The FPS ERGAL piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. Each FPS piston head is made of ergal and it is also anodized for smooth surface finish. This is the most advanced version with 6 ventilation holes. This piston head is the most traditional of our production and improves the performance of your aeg, double o-ring and ball-bearing. The piston head is constructed out of CNC ERGAL for durability and precision.
    This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.
    Compatibility :

    Version 2, Version 3, Version 6, Version 7 ( M4, M16, MP5, AK, G36, M14, P90, SIG,STEYR AUG etc ...).

    Compatible with the following brands :

    TOKYO MARUI, G&G, VFC, ICS, KWA, H&K, JING GONG, CYMA, SRC, UMAREX, CLASSIC ARMY, ECHO 1 etc...


    Weight: 11.9 grams
    100% MARUI COMPATIBLE
    100% MADE IN ITALY
    FPS Softair double o-ring ball bearing AEG Piston Head

  • FPS Softair double o-ring ball bearing light Piston Head

    FPS CNC ERGAL Double O-Ring Ball Bearing AEG Piston Head (TPPE).

    The FPS ERGAL piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. Each FPS piston head is made of ergal and it is also anodized for smooth surface finish. This is the most advanced version with 8 ventilation holes for higher speed and rate of fire, double o-ring and ball-bearing. The piston head is constructed out of CNC ERGAL for durability and precision.

    This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    Compatibility :

    Version 2, Version 3, Version 6, Version 7 ( M4, M16, MP5, AK, G36, M14, P90, SIG,STEYR AUG etc ...).

    Compatible with the following brands :

    TOKYO MARUI, G&G, VFC, ICS, KWA, H&K, JING GONG, CYMA, SRC, UMAREX, CLASSIC ARMY, ECHO 1 etc...

    Weight: 11.3 grams
    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair double o-ring ball bearing light Piston Head

  • FPS Softair double o-ring ball bearing high speed Piston Head

    FPS CNC ERGAL Double O-Ring Ball Bearing AEG Piston Head Advanced Type (TPAVN).

    The FPS ERGAL piston head is a great upgrade that will increase the efficiency of airflow through the cylinder.  This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. Each FPS piston head is made of ergal and it is also anodized for smooth surface finish. This is the most advanced version with 8 ventilation holes for higher speed and rate of fire, double o-ring and ball-bearing. The piston head is constructed out of CNC ERGAL for durability and precision.

    This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    Compatibility :

    Version 2, Version 3, Version 6, Version 7 ( M4, M16, MP5, AK, G36, M14, P90, SIG,STEYR AUG etc ...).

    Compatible with the following brands :

    TOKYO MARUI, G&G, VFC, ICS, KWA, H&K, JING GONG, CYMA, SRC, UMAREX, CLASSIC ARMY, ECHO 1 etc...

    Weight: 11.2 grams

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair double o-ring ball bearing high speed Piston Head

  • FPS Softair ball bearing Piston Head with X-RING

    FPS CNC ERGAL Double O-Ring Ball Bearing AEG Piston Head (XPGE).

    XPGE new version with X-RING and one piece plastic shim for AOE. The FPS ERGAL piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. Each FPS piston head is made of ergal and it is also anodized for smooth surface finish. This is the most advanced version with 6 ventilation holes. This piston head is the most traditional of our production and improves the performance of your aeg, double o-ring and ball-bearing. The piston head is constructed out of CNC ERGAL for durability and precision. This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    Compatibility :
    Version 2, Version 3, Version 6, Version 7 ( M4, M16, MP5, AK, G36, M14, P90, SIG,STEYR AUG etc ...).

    Compatible with the following brands :
    TOKYO MARUI, G&G, VFC, ICS, KWA, H&K, JING GONG, CYMA, SRC, UMAREX, CLASSIC ARMY, ECHO 1 etc...

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair ball bearing Piston Head with X-RING

  • FPS Softair double o-ring ball bearing Piston Head X-RING

    FPS CNC ERGAL Double O-Ring Ball Bearing AEG Piston Head (XPPE).

    New version whith X-RING and one piece plastic shim for AOE. The FPS ERGAL piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. Each FPS piston head is made of ergal and it is also anodized for smooth surface finish. This is the most advanced version with 8 ventilation holes for higher speed and rate of fire, double o-ring and ball-bearing. The piston head is constructed out of CNC ERGAL for durability and precision. This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas. 

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair double o-ring ball bearing Piston Head X-RING

  • FPS Softair POM double o-ring ball bearing AEG Piston Head

    FPS CNC POM Double O-Ring Ball Bearing AEG Piston Head (TPPD).

    The FPS POM piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. This is the most advanced version with 6 ventilation holes. This piston head is the ligthest of our piston heads and improves the performance of your aeg, double o-ring and ball-bearing. This piston head is constructed out of CNC POM for durability and precision.

    This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    Weight: 8,7 grams

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair POM double o-ring ball bearing AEG Piston Head

  • FPS Softair ball bearing POM Piston Head with X-RING

    FPS CNC POM Double O-Ring Ball Bearing AEG Piston Head (XPPD).

    XPPD new version with X-RING and one piece plastic shim for AOE. The FPS POM piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. This is the most advanced version with 6 ventilation holes. This piston head is the ligthest of our piston heads and improves the performance of your aeg, double o-ring and ball-bearing. This piston head is constructed out of CNC POM for durability and precision. This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    Compatibility :
    Version 2, Version 3, Version 6, Version 7 ( M4, M16, MP5, AK, G36, M14, P90, SIG,STEYR AUG etc ...).

    Compatible with the following brands :
    TOKYO MARUI, G&G, VFC, ICS, KWA, H&K, JING GONG, CYMA, SRC, UMAREX, CLASSIC ARMY, ECHO 1 etc...

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair ball bearing POM Piston Head with X-RING

  • FPS Softair CNC Ball Bearing Piston Head Pressure Deviation (TPAE)

    The FPS ERGAL piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB.

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair CNC Ball Bearing Piston Head Pressure Deviation (TPAE)

  • FPS Softair ball bearing POM Piston Head double oring and adjustable AOE

    CNC POM Double O-Ring Ball Bearing AEG Piston Head with adjustable AOE (TPPA)

    The FPS POM piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. This piston head allows to adjust the length of the piston of 1-2-3 or 4 mm, and it can also be used without shims. Find a perfect AOE improves the reliability of your gun. This piston head is one of the most ligthest of our production and improves the performance of your aeg, double o-ring and ball-bearing. The piston head is constructed out of CNC POM for durability and precision. This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair ball bearing POM Piston Head double oring and adjustable AOE

  • FPS Softair ball bearing POM Piston Head for high speed ROF

    POM piston head designed for high rof and to increase the silence of the replica thanks to the very small knocking surface (TPNS). It is the lightest among those produced by the FPS for rifles with gusts over 30 BBs / second. Its adoption lightens the weight of the piston and piston head with a significant reduction in mechanical stress and noise. The particular conformation of the striking part (conical degrading towards the center with different angles) ensures that the ventilation holes are never closed by the rubber of the cylinder head, without however leaving too much air between the cylinder head and piston head. All this ensures a perfect anti-vacuum system without ever producing power losses. This piston head was developed thanks to the experience of Nico Saccocci of NikkSakk.Extreme.Airsoftcustom.


    The product is supplied with a metallic bearing and washer in orange-colored technopolymer. For preparations of replicas with extreme rates our technical team recommends the use of the washer to lighten the beating mass.
    Technical specifications:

    Weight: 8.3 grams (with metal pad)
    Weight: 5.5 grams (with technopolymer washer)

    100% COMPATIBLE MARUI
    100% MADE IN ITALY

    FPS Softair ball bearing POM Piston Head for high speed ROF

  • FPS Softair ball bearing POM Piston Head X-RING and adjustable AOE

    CNC POM Double O-Ring Ball Bearing AEG Piston Head with adjustable AOE (XPPA), new version with X-RING technology.

    The FPS POM piston head is a great upgrade that will increase the efficiency of airflow through the cylinder. This piston head has ports on the front to push out the o-ring as it moves forwards, this ensures that all of the air in the cylinder is being pushed out to propel the BB. The ball bearings help reduce tension created by the spring compressing and expanding, this combined with a ball bearing spring guide is the optimal set up to keep your spring in good shape. This piston head allows to adjust the length of the piston of 1-2-3 or 4 mm, and it can also be used without shims. Find a perfect AOE improves the reliability of your gun. This piston head is one of the most ligthest of our production and improves the performance of your aeg, double o-ring and ball-bearing. The piston head is constructed out of CNC POM for durability and precision. This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    100% MARUI COMPATIBLE
    100% MADE IN ITALY

    FPS Softair ball bearing POM Piston Head X-RING and adjustable AOE

  • GATE CNC HIGH SPEED Piston Head

    The piston head designed for the most demanding DSG and speed builds, helping achieve the best results and overcome limits. Thanks to the use of 10 vents, airflow significantly increases improving sealing. The ultra-lightweight POM material together with CNC machining ensures repeatability of shots, perfect head-to-cylinder seal, high RPS ratio, and eliminates FPS drops. The adjustable AOE makes it essential for every speed build. 

    Features:

    • Designed especially for most demanding DSG and speed builds
    • 10 vents enhancing airflow and sealing
    • Ultra-lightweight POM material
    • CNC machining
    • Perfect head-to-cylinder seal
    • AOE spacer included
    • No AEG modification required
    • Dedicated especially to pros and skilled users
    • Piston head weight 2.7 g (without bearing)

    Compatibility:

    • Ideal for max M140 spring power
    • All standard AEG cylinders
    • All standard AEG cylinder heads
    • All standard AEG pistons
    • O-rings 19x2.4 mm

    Kit contents:

    • HIGH SPEED Piston Head – POM
    • AOE spacer
    • 1 bearing
    • 2 installation screws
    • 2 o-rings
    • QR Code containing quickstart guide
    GATE CNC HIGH SPEED Piston Head

  • Maxx Model CNC Aluminum Double O-Ring Ball Bearing AEG Piston Head

    Maxx Model CNC Aluminum Double O-Ring Ball Bearing AEG Piston Head

  • FPS Softair technopolymer / Carbon fiber piston head Xring

    Xring Carbon fiber reinforced technopolymer piston head designed for high rof and to increase the silence of the aeg (XPAVPCF) It is the lightest among those produced by the FPS for rifles with gusts over 30 BBs / second. Its adoption lightens the weight of the piston and piston head with a significant reduction in mechanical stress and noise. The particular conformation of the striking part (conical degrading towards the center) ensures that the ventilation holes are never closed by the rubber of the cylinder head, without however leaving too much air between the cylinder head and piston head. All this ensures a perfect anti-vacuum system without ever producing power losses. For preparations of replicas with extreme rates our technical team recommends the use of the washer to lighten the beating mass. Supplied with VITON Xring for maximum smoothness and chemical resistance to lubricants.

    FPS Softair technopolymer / Carbon fiber piston head Xring

  • FPS Softair POM / Carbon fiber piston head

    Carbon fiber reinforced pom piston head designed for high rof and to increase the silence of the aeg (TPAVPCF) It is the lightest among those produced by the FPS for rifles with gusts over 30 BBs / second. Its adoption lightens the weight of the piston and piston head with a significant reduction in mechanical stress and noise. The particular conformation of the striking part (conical degrading towards the center) ensures that the ventilation holes are never closed by the rubber of the cylinder head, without however leaving too much air between the cylinder head and piston head. All this ensures a perfect anti-vacuum system without ever producing power losses. For preparations of replicas with extreme rates our technical team recommends the use of the washer to lighten the beating mass. Supplied with VITON oring for maximum smoothness and chemical resistance to lubricants

    100% COMPATIBLE MARUI
    100% MADE IN ITALY

    FPS Softair POM / Carbon fiber piston head

Choose your Cylinder head. Basically, we advise you to choose the Balystik CNC aluminum Cylinder head model which is very versatile and resistant, but you can choose another model !

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • Balystik CNC aluminum V2 Cylinder head

    Balystik AEG GearBox Cylinder Head version 2

    • Great Upgrade for any gearbox
    • Made of aluminum and anodized for smooth surface finish
    • Ultra lightweight product with less than 10gr
    • Build by CNC process to ensure a product with maximum durability and precision
    • The dual orings ensure a perfect seal on all cylinders on the market
    • Powerful 3.6mm rear bumper that absorbs the shock from the piston head
    • Additional front bumper on the nozzle side to prevent any vibration between the gearbox and the cylinder head
    • Perfect for most : M4 , M16 , SR16 , MP5 , MC51 , G3 , M249 , LR300
    • Compatible with ICS, Tokyo Marui, Classic Army, VFC
    Balystik CNC aluminum V2 Cylinder head

  • SHS V2 Cylinder head with pad

    SHS V2 Cylinder head with pad

  • Specna Arms aluminium cylinder head V2/V3 for AEG

    Specna Arms aluminium cylinder head V2/V3 for AEG

  • POINT Aluminum Silent Cylinder Head V2

    POINT Aluminum Silent Cylinder Head V2

  • FPS Softair V2 CNC Cylinder Head with 70 degrees

    • FPS  Airsoft AEG Gear Box / Mech Box Cylinder Head version 2 made of ERGAL (TC02B).
    • Great Upgrade for any gear box.
    • Each FPS Cylinder head is made of ERGAL and it is also anodized for smooth surface finish.
    • The Cylinder heads are CNC manufactured to ensure a product with maximum durability and precision.
    • Powerful built in UREPAN bumper that absorbs the shock from the piston head.

    Among the excellent characteristics of UREPAN are:

    - high dynamic load capacity
    - high abrasion and tear propagation resistance
    - highest modulus of elasticity of all elastomers
    - excellent mechanical wear resistance
    - high impact resilience
    - low compression set
    - non-marking floor protection
    - non-staining wheel tread material

    Hardness of orange rubber = 70 degrees shore which makes it suitable for multipurpose use.

    Furthermore, UREPAN offers good chemical resistance to mineral oils and greases as well as various solvents. UREPAN is recommended for all applications with high demands regarding load capacity, rebound resilience, speed and durability.

    • Perfect for most : M4 , M16 , SR16 , MP5 , MC51 , G3 , M249 , LR300 and any Version 2 gearbox AEG.
    • Compatible with ICS, Tokyo Marui, Classic Army, VFC and more.
    • This product is designed and manufactured entirely in Italy by technicians who have years of experience in the repair and modification of airsoft replicas.
    • 100% MADE IN ITALY
    • 100% MARUI COMPATIBLE
    FPS Softair V2 CNC Cylinder Head with 70 degrees

  • FPS Softair V2 CNC Cylinder Head with 60 degrees

    • FPS  Airsoft AEG Gear Box / Mech Box Cylinder Head version 2 made of ERGAL (TC02C).
    • Great Upgrade for any gear box.
    • Each FPS Cylinder head is made of ERGAL and it is also anodized for smooth surface finish.
    • The Cylinder heads are CNC manufactured to ensure a product with maximum durability and precision.
    • Powerful built in UREPAN bumper that absorbs the shock from the piston head.

    Among the excellent characteristics of UREPAN are:

    - high dynamic load capacity
    - high abrasion and tear propagation resistance
    - highest modulus of elasticity of all elastomers
    - excellent mechanical wear resistance
    - high impact resilience
    - low compression set
    - non-marking floor protection
    - non-staining wheel tread material

    Hardness of rubber = 60 degrees shore which makes it suitable for use on custom DMR, to protect notoriously fragile gerboxes and reduce the noise of the replica.

    Furthermore, UREPAN offers good chemical resistance to mineral oils and greases as well as various solvents. UREPAN is recommended for all applications with high demands regarding load capacity, rebound resilience, speed and durability.

    • Perfect for most : M4 , M16 , SR16 , MP5 , MC51 , G3 , M249 , LR300 and any Version 2 gearbox AEG.
    • Compatible with ICS, Tokyo Marui, Classic Army, VFC and more.
    • This product is designed and manufactured entirely in Italy by technicians who have years of experience in the repair and modification of airsoft replicas.
    • 100% MADE IN ITALY
    • 100% MARUI COMPATIBLE
    FPS Softair V2 CNC Cylinder Head with 60 degrees

  • MAxx Model CNC Aluminum Double Air Seal & Damper AEG Cylinder Head

    MAxx Model CNC Aluminum Double Air Seal & Damper AEG Cylinder Head

Choose you nozzle. We have already selected the right model and the best brands for you. Remember that the nozzle material (aluminium or polymer) is not important compare to the shape, seal effect and smooth slide on the cylinder head. All the nozzle above include oring seal.

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • FPS Softair Nozzle with inner O-Ring for M4 AEG

    The FPS Air Nozzle is a replacement nozzle for AEG type guns. Its ERGAL CNC construction (7075 aluminium) and internal o-ring makes it a great upgrade from a factory plastic air nozzle. Each FPS air nozzle is also anodized for smooth surface finish. Be sure to use pure silicone oil when lubricating the nozzle stem on your cylinder head before installing this nozzle. Increase your power and efficiency with this better sealing and more durable nozzle. This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    100% Marui compatible

    If you have any doubt regarding other brand compatibility, please check you original nozzle lenght before making the purchase

    100% Made in italy

    FPS Softair Nozzle with inner O-Ring for M4 AEG

  • FPS Softair Delrin Nozzle with inner O-Ring for M4 AEG

    The FPS Air Nozzle is a replacement nozzle for AEG type guns. Its Delrin CNC construction and internal o-ring makes it a great upgrade from a factory plastic air nozzle. Each FPS air nozzle is also anodized for smooth surface finish. Be sure to use pure silicone oil when lubricating the nozzle stem on your cylinder head before installing this nozzle. Increase your power and efficiency with this better sealing and more durable nozzle. This product is designed and manufactured entirely in Italy, by technicians who have years of experience in the repair and modification of airsoft replicas.

    100% Marui compatible

    If you have any doubt regarding other brand compatibility, please check you original nozzle lenght before making the purchase

    100% Made in italy

    FPS Softair Delrin Nozzle with inner O-Ring for M4 AEG

  • Maxx Model CNC Aluminum Double O-Ring Nozzle (21.25mm)

    Maxx Model CNC Aluminum Double O-Ring Nozzle (21.25mm)

  • SHS Aluminium Air Seal Nozzle for M4 Series AEG

    SHS Aluminium Air Seal Nozzle for M4 Series AEG

  • SLONG AIRSOFT Nozzle with inner O-Ring for M4 AEG

    100% Marui compatible

    SLONG AIRSOFT Nozzle with inner O-Ring for M4 AEG

We advice 18:1 or 16:1 ratio wich is very good balance between torque and speed. Please note that for reliability of your replica only 18:1 gearset can be installed with a brushless motor.

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • SHS 18:1 torque CNC gearset

    SHS 18:1 torque CNC gearset

  • SHS 16:1 speed CNC gearset

    SHS 16:1 speed CNC gearset

  • SHS 13:1 super high speed CNC gearset

    SHS 13:1 super high speed CNC gearset

  • SHS 12:1 extreme high speed CNC gearset

    Recommanded spring power : M100 or less, (330 FPS max)
    SHS 12:1 extreme high speed CNC gearset

  • BIG DRAGON metal / titanium 18:1 torque gearset

    • A set of extremely durable gears 18:1 dedicated to the V2 and V3 gearbox.
    • They were made of an alloy of steel and titanium, thanks to which their strength is increased.
    • The final machining of the gears was carried out on CNC machine tools, guaranteeing the precision of workmanship.
    • They are perfect for springs not stronger than 130 m/s.
    BIG DRAGON metal / titanium 18:1 torque gearset

  • BIG DRAGON metal / titanium 16:1 speed gearset

    • A set of extremely durable gears speed 16:1 dedicated to the V2 and V3 gearbox.
    • They were made of an alloy of steel and titanium, thanks to which their strength is increased.
    • The final machining of the gears was carried out on CNC machine tools, guaranteeing the precision of workmanship.
    • They are perfect for springs not stronger than 120 m/s.
    BIG DRAGON metal / titanium 16:1 speed gearset

  • BIG DRAGON metal / titanium 13:1 high speed gearset

    • A set of extremely durable gears super high speed 13:1 dedicated to the V2 and V3 gearbox.
    • They were made of an alloy of steel and titanium, thanks to which their strength is increased.
    • The final machining of the gears was carried out on CNC machine tools, guaranteeing the precision of workmanship.
    • They are perfect for springs not stronger than 110 m/s.
    BIG DRAGON metal / titanium 13:1 high speed gearset

  • Arcturus 13:1 Super High Speed CNC GearSet

    A set of steel gears with a 13:1 ratio for AEG. They are manufactured on CNC machines to guarantee solidity and durability. Ideal compatibility with V2 or V3 type gearboxes. By combining these gears with a High Speed type motor, adding an 11.1v lipo battery, this will allow you to reach a rate of fire of around 25-28rps.

    Arcturus 13:1 Super High Speed CNC GearSet

Very important part that need to be upgraded to avoid any break. We recommend FPS softair Tappet plate series for the quality / price

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • FPS Softair Reinforced tappet plate for V2 Gearbox

    The FPS Reinforced AEG Tappet Plate for V2 gearbox is constructed out of polymer and is designed to be attached to the air nozzle and sector gear.  This process controls the feeding of BBs from the magazine into the hop up chamber.

    Features:

    • Polymer Construction
    • Reinforced Design
    • Strong / Flexible
    • Compatibility : V2 gearbox

    Please Note:

    • Professional installation is recommended. Improper use or improper installation of upgrade parts are 99% of the time the cause of failures of these items.

    100% MADE IN ITALY

    FPS Softair Reinforced tappet plate for V2 Gearbox

  • FPS Softair carbon fiber Reinforced Tappet Plate for V2 AEG

    FPS carbon fiber Reinforced AEG Tappet Plate Ver. 2 is constructed out of polymer and is designed to be attached to the air nozzle and sector gear. This process controls the feeding of BBs from the magazine into the hop up chamber.

    Specifications:

    • Manufacturer: FPS Softair
    • Model: Ver. 2 Tappet Plate
    • Package Includes: One (1) Tappet Plate

    Features:

    • Carbon Fiber Polymer Construction
    • Reinforced Design
    • Strong / Flexible

    Please Note:

    • Professional installation is recommended. Improper use or improper installation of upgrade parts are 99% of the time the cause of failures of these items.
    • 100% MARUI COMPATIBLE
    • 100% MADE IN ITALY
    FPS Softair carbon fiber Reinforced Tappet Plate for V2 AEG

  • Guarder Tappet Plate V2

    Guarder Tappet Plate V2

  • POINT tappet plate for version 2 gearbox

    POINT tappet plate for version 2 gearbox

  • Prometheus PERFECT Tappet Plate for AEG Version 2 Gearbox

    Prometheus PERFECT Tappet Plate for AEG Version 2 Gearbox

  • SHS tappet plate for V2 gearbox

    SHS tappet plate for V2 gearbox

The replica already include a mosfet system out of the box, but you have the possibility to choose an advanced model

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

  • GATE TITAN EXPERT module V2 - Rear

    The TITAN is the most advanced Mosfet in the Gate range. It is the first MOSFET in the world for Gearbox V2 to integrate 8 optical sensors, it has many interesting functions including:

    • Active Braking Technology
    • Increases responsiveness and rate of fire
    • Electronic fuse
    • Two programmable Precocking modes
    • Trigger sensitivity in 5 modes.
    • Programmable burst 1 to 3 shots
    • compatible with 14.8v batteries
    • No physical contactor: detection of the trigger tail, cut-off lever and selector plate is done with 5 sensors
    • Programmable in firing mode with the possibility of adding a configurable burst mode to the replica.
    • Low voltage detection for LIPO batteries.
    • Version of the TITAN sold without the USB key and the programming card.

    Content :

    • 1x TITAN with rear wiring
    • 1x Instructions

    109561.jpg?time=1698321933690

    109563.jpg?time=1698322278942

    79,08 €
    GATE TITAN EXPERT module V2 - Rear

    79,08 €
  • JEFFTRON Mosfet Leviathan optical Bluetooth V2 Rear

    The Leviathan - V2 optical is one of the most advanced ETU (electronic trigger unit) on the market. It combines optical and switch sensors for better handling and durability.

    • Build-in wireless communication for quick setup using iOS or Android smartphones!
    • Tactile trigger switch has travel only 0,13mm long for ultimate hair trigger feeling
    • Unique Real feel trigger system (RFTS) with integrated spring simulates trigger resistance like in the real gun. It adds secondary resistance with release after the fire. RFTS was designed by professional gunsmith for more realistic feel from shooting
    • External output and input port serves for custom accessories
    • Real time response for change settings -> immediately test result
    • Easy installation into the gearbox (fully integrated inside the gearbox instead of the original trigger contacts)

    MAIN FUNCTIONS:

    • Adds new shooting modes independent for every position on the fire selector (SAFE - SEMI - AUTO)
    • Three adjustable bursts (range 2 - 20 shots)
    • It preserves empty magazine detection like the original gun
    • Rate of fire can be reduce to 40%. It add breaks between shots to reduce RoF. It gives fast trigger response even with very low rate of fire, just like in a real gun
    • Adjustable strength active braking (can be disabled)
    • Pre-cocking function for instant shot on SEMI fire
    • Delay between shots adds time in which isn't possible to shoot, it simulates the delay from gun reload or recoil (range 0,1 - 4,0 seconds)
    • Electronic fuse set sensitivity for high current detection to avoid any damage if something goes wrong
    • Low battery indication for 2S - 4S li-pol and 3S - 4S li-fe
    • Virtual magazine simulates low capacity magazines, it will force the gun to stop shooting when it reach 0. There can be set warning after shot before empty magazine and how it will be reloaded
    • On the board are input and output ports for controlling external devices or Leviathan
    • Statistics screen shows shooting output with cycle timing, motor current consumption, rate of fire and temperatures. It allows you to do fine-tune gearbox upgrade
    • Application shows actual battery voltage value. Color lines indicates battery charge status where green is OK, orange will warn after each shot and red will not allow to shoot
    • User can save multiple settings under profiles
    • Update function fixes bugs and adds new features to the device
    • There are three shot counters. Total count every shot during the device lifetime. User counter can be reset by user anytime. Power-up counter is reset by battery connection
    • Error log shows errors made during the device life also can be erased by user
    • For better security wireless connection can be disable by the selector switch (can be deactivated)
    • Leviathan monitors current, voltage and temperature to avoid any damage when something go wrong.
    • Motor vibrates and beeps as a feedback for user
    • Programmed settings are saved in the Leviathan memory immediately after their change, so you can immediately test it and settings aren't lost when is battery disconnected or lost connection with smartphone
    • New functions are for free for every user via online update function

    FIRE MODES:

    • Independent for every position on the fire selector (SAFE - SEMI - AUTO)
    • SAFE: no responding on the trigger pull.
    • Semi: it fires single shot per trigger pull.
    • Semi/BurstX: short trigger pull fires single shot, long trigger pull fires burst.
    • Binary trigger: it fires single shot when trigger is pulled and another single shot when is released.
    • BurstX: gun shoot burst per trigger pull.
    • BurstX+BurstY: short trigger press fires burstX, long trigger press makes burstX+burstY fire.
    • BurstX/Full: short trigger press fires burstX, long trigger press makes auto fire.
    • Full: gun makes auto fire until releasing trigger.
    • Virtual reload: pull trigger to reload virtual magazine

    EXTERNAL INPUT:

    • OFF: Every signal to Input terminal is ignored.
    • External trigger: gun trigger is disabled and replaced by micro switch connected to Input (SIG and GND)
    • Burst-3 trigger: micro switch connected to Input (SIG and GND) make 3 burst fire when it is pressed. Gun trigger is still functional.
    • AUG trigger: selector plate detection is disabled. Gun trigger is set to selector on semi. Micro switch connected to Input (SIG, GND) is set to selector on auto.
    • Empty mag (NO): Micro switch activates empty magazine detection, when is connected SIG with GND.
    • Empty mag (NC): Micro switch activates empty magazine detection, when is disconnected SIG with GND.
    • Virtual reload: Micro switch activates virtual magazine reload, when is connected SIG with GND.

    EXTERNAL OUTPUT:

    • OFF: output terminal works only if the Input terminal activates it.
    • Motor: output terminal is ON with gun motor + with IN activation.
    • Motor + Xs: output terminal is ON with gun motor with time delay after gun motor is deactivated + with IN activation.
    • Always on: the output terminal is constantly activated.

    Leviathan – V2 optical supports these airsoft guns:

    • M4, M16, HK416, AR15 with V2 gearbox according to TM design
    • M4 with V2 gearbox from Krytac company
    • SR25 with V2 gearbox according to TM design
    • MP5 with V2 gearbox according to TM design
    • G3 with V2 gearbox according to TM design
    • M249 with V2 gearbox according to TM design
    • M107 BARRETT from Snow wolf company
    • And others ...

    Leviathan - V2 optical is not compatible with these gearboxes:

    • KWA gearbox V2.5
    • S&T or Arcturus gearbox V2
    • ICS SSS gearbox V2
    • Ares Amoeba gearbox V2
    • G&G G2 gearbox V2
    • APS silver edge gearbox V2
    • Gearbox V2 with microswitch
    • And others ...

     TECHNICAL SPECIFICATIONS:

    Easy installation inside the gearbox version 2, compatible with Tokyo Marui standard : You don‘t have to modify the gearbox V2 from the Krytac company. Simply cut the Leviathan bottom board. It uses optical sensor actuated by sector gear cam for perfect semi and burst fire timing. For fire selector position is used optical sensor too - it works with sticker provided with Leviathan      

    • Tactile trigger switch makes short click for great hair trigger mod.
    • Unique real feel trigger system (RFTS) simulates trigger feeling like in the real gun. It adds secondary resistance with release after the fire. Feeling is comparable to shooting with real caliber 22lr in AR15
    • Thanks to advanced electronics, Leviathan - V2 optical can be used with any common gearbox upgrade and gun rate of fire
    • Completely made wiring allows the fastest and the easiest installation into the gun, it is long enough for all kind of weapons with battery placed in the front. No soldering is needed
    • For easier installation, there are connectors on the battery cables for disconnecting part with the T-plug connector and fuse
    • The wire length between the gearbox and the battery connector is 385mm
    • There are high quality power wires 1,5 qmm (AWG16) with thin and hard MPPE insulation and signal blue wire 0.34 qmm (AWG24) with MPPE insulation
    • Power wires outer diameter is only 2,06 mm and blue wire 1,24 mm
    • Board covered by conformal coating, it protect Leviathan against damage from water
    • On the board is input port for controlling output port, 3rd burst, external trigger, magazine reload, etc. and output port for the hop-up chamber BBs illumination, powering electric magazine, flashlight, laser, etc.
    • For right pre-cocking function is necessary to have in the gearbox functional antireverse latch. WARNING: it increases wear and tear on the gearbox.
    • Specified for common batteries up to 17V (Ni-xx 8.4 - 12V, lipol 7.4 - 14.8V)
    • Device increases gun rate of fire and battery holds longer, than with basic wiring
    • With active braking ON piston isn't partially stretched, spring is fully released, parts in mechabox aren't under strain and nozzle locks hop-up chamber in greater part (depends on ROF)
    • In weapons with very high rate of fire (ROF) active brake solves multiple shots in semi mode
    • The braking effect is the most powerful with high torque motor. Note: Lower braking intensity spares the motor coils.
    • Remove from the gearbox: cut off lever, trigger, trigger contacts and trigger block, you will not need them with the Leviathan - V2 optical

    PACKING:

    • Leviathan - V2 optical drop-in electronic module with wiring to rear, T-plug connector, 40A mini fuse and faston connectors to the motor
    • Screw with washer for securing device in the gearbox
    • Black Leviathan sticker 40 mm
    • Foam to keep device in place

    SAFETY WARNING:

    • Installation of this device into the gearbox requires advanced technician skills!
    • Please read these informations before installing your device to prevent any damage.
    • Short circuit or incorrectly connected battery will cause immediate damage to the device which is not covered by the warranty. It can lead to fire or even battery explosion.
    • Disconnect battery, when you aren't using the gun! Otherwise you will fully discharge the battery. Because the device drains small amount of current from the bettery all the time.
    • Do not connect battery when gun pointing towards you, another person or an animal.
    • Do not modify, repair and put into any kind of liquids or thermal shock the Leviathan - V2 optical.

    87,42 €
    JEFFTRON Mosfet Leviathan optical Bluetooth V2 Rear

    87,42 €
  • T238 V1.42 Digital Trigger Unit Programmable mosfet V2

    The DTU V1.42 for Tokyo Marui V2 gearbox is a multifunctional MOSFET switch. Specifically designed for AIRSOFT, Gel Ball Blaster, other V2 gearboxes with semi-automatic and fully automatic functions. this mosfet version is already wired.

    Functions:

    • Supports up to 14.8V battery.
    • Binary trigger. Put the selector in semi-auto position, pull and hold the trigger for 3 seconds will change the semi-auto function into binary trigger shooting mode.
    • Auto-loading function is designed for gel ball blaster magazines with motor inside, when changing the magazine, the magazine motor will run automatically for 0.5 second.
    • PRE-COCKING.The default postition of the piston is adjustable is semi-auto model.Per-cocking function can be implementing,zero trigger delay.
    • DTU overheat protection.When the DTU is overheated,after the trigger is pulled,the motor will give a beep prompt until it is automatically restarted after cooling.
    • Low battery voltage protection:the default setting is 7.4V battery.Change the battery when hearing‘beep,beep,beep,beep’4 times low voltage warning sound.
    • Active braking.The energy that support the active brake function comes from the inertia of motor, stop the piston without delay. The effect of active brake is significant on high torque motor.
    • Fast speed of respond.This module is powered by small current,the current flow through the MOSFET directly to the motor,provide higher current to increase the rate of fire and speed of respond.
    • Block-up protection.When gearboxBlock-up occurs, the system stops working and emits an elongated 'beep' sound. Please check the wave box immediately by power off.
    • Multiple shooting modes.The system includes multiple shooting modes,those modes can be selected by fire select switch.
    • Gearbox protection.The active brake prevents the over-spin of gears,this solve the issue that single shot changes to multiple shot under high voltage.meanwhile,the spring is fully released in semi-auto model and parts in the gearbox are not under strain,increase the life cycle of your gearbox.

    Package Included:

    • 1 X Digital trigger unit V1.42
    • 1 X English Manual
    • 1 X Badge
    • 1 X Small bag accessories

    37,42 €
    T238 V1.42 Digital Trigger Unit Programmable mosfet V2

    37,42 €
  • T238 V1.7 optical mosfet for V2 gearbox

    The DTU V1.7 optical Sensor Version for V2 Tokyo Marui gearbox is a multifunctional MOSFET switch. Specifically designed for AIRSOFT, Gel Ball Blaster, other V2 gearboxes with semi-automatic and fully automatic functions. this mosfet version is already wired.

    Functions:

    1. Supports up to 14.8V battery.
    2. Binary trigger. Put the selector in semi-auto position, pull and hold the trigger for 3 seconds will change the semi-auto function into binary trigger shooting mode.
    3. Auto-loading function is designed for gel ball blaster magazines with motor inside, when changing the magazine, the magazine motor will run automatically for 0.5 second.
    4. PRE-COCKING.The default postition of the piston is adjustable is semi-auto model.Per-cocking function can be implementing,zero trigger delay.
    5. ETU overheat protection.When the DTU is overheated,after the trigger is pulled,the motor will give a beep prompt until it is automatically restarted after cooling.
    6. Low battery voltage protection:the default setting is 7.4V battery.Change the battery when hearing‘beep,beep,beep,beep’4 times low voltage warning sound.
    7. Active braking.The energy that support the active brake function comes from the inertia of motor, stop the piston without delay. The effect of active brake is significant on high torque motor.
    8. Fast speed of respond.This module is powered by small current,the current flow through the MOSFET directly to the motor,provide higher current to increase the rate of fire and speed of respond.
    9. Block-up protection.When gearboxBlock-up occurs, the system stops working and emits an elongated 'beep' sound. Please check the wave box immediately by power off.
    10. Multiple shooting modes.The system includes multiple shooting modes,those modes can be selected by fire select switch.
    11. Gearbox protection.The active brake prevents the over-spin of gears,this solve the issue that single shot changes to multiple shot under high voltage.meanwhile,the spring is fully released in semi-auto model and parts in the gearbox are not under strain,increase the life cycle of your gearbox.

    Package Content:

    • Digital trigger unit V1.7     X1
    • Manual     X1
    • Badge    X1
    • Small bag accessories    X1

    Shooting Modes:

    • SAFE:This model is completely the same as original safe model.The trigger is stopped by safety lever.
    • SEMI:This model can be programmed to implementing semi-auto,double stroke single shot,3-rounds burst to 6 rounds burst,the default model is semi auto.
    • AUTO:This model can be programmed to implementing full-auto,3-round burst,6-round burst and 9-round burst,the default model is full-auto.

    49,92 €
    T238 V1.7 optical mosfet for V2 gearbox

    49,92 €
  • T238 V2.0 optical bluetooth mosfet for V2 gearbox

    The V2.0 for V2 bluetooth version gearbox is a multifunctional MOSFET switch which can be programmed by smart phone via bluetooth.

    • Adopts a high speed processor, 8 optical sensors and 2 high power MOSFET chips.
    • Designed for AIRSOFT, Gel Ball Blaster and other V2 gearboxes with semi-automatic and fully automatic functions.

    Features:

    1. Supports up to 14.8V battery.
    2. Bluetooth module : Integrated bluetooth wireless communication module, use smart phone to program through bluetooth, can download Android / IOS free APP.
    3. Binary trigger : Put the selector in semi-auto position, pull and hold the trigger for 3 seconds will change the semi-auto function into binary trigger shooting mode.
    4. Auto-loading function is designed for gel ball blaster magazines with motor inside, when changing the magazine, the magazine motor will run automatically for 0.5 second.
    5. PRE-COCKING.The default postition of the piston is adjustable is semi-auto model.Per-cocking function can be implementing,zero trigger delay.
    6. ETU overheat protection.When the DTU is overheated,after the trigger is pulled,the motor will give a beep prompt until it is automatically restarted after cooling.
    7. Low battery voltage protection:the default setting is 7.4V battery.Change the battery when hearing‘beep,beep,beep,beep’4 times low voltage warning sound.
    8. Active braking.The energy that support the active brake function comes from the inertia of motor, stop the piston without delay. The effect of active brake is significant on high torque motor.
    9. Fast speed of respond.This module is powered by small current,the current flow through the MOSFET directly to the motor,provide higher current to increase the rate of fire and speed of respond.
    10. Block-up protection.When gearboxBlock-up occurs, the system stops working and emits an elongated 'beep' sound. Please check the wave box immediately by power off.
    11. Multiple shooting modes.The system includes multiple shooting modes,those modes can be selected by fire select switch.
    12. Gearbox protection.The active brake prevents the over-spin of gears,this solve the issue that single shot changes to multiple shot under high voltage.meanwhile,the spring is fully released in semi-auto model and parts in the gearbox are not under strain,increase the life cycle of your gearbox.

    Modes:

    • Safe – This mode is completely the same as original safe mode. The trigger can be pulled but nothing happens. The default mode is safe, however this mode can be programmed to semi-auto, double stroke single shot, 3-round burst to 6-round burst.
    • Semi – The default mode is semi, however this mode can be programmed to semi-auto, double stroke single shot, 3-round burst to 6-round burst.
    • Auto – The default mode is full-auto, however this mode can be programmed to full-auto, 3-round burst, 6-round burst, or 9-round burst.

    Package Content:

    • Digital trigger unit V2.0   X1
    • Manual    X1
    • Badge     X1
    • Small bag accessories   X1
    • Insulation sticker   X1

    80,75 €
    T238 V2.0 optical bluetooth mosfet for V2 gearbox

    80,75 €
  • GATE TITAN II Expert version Bluetooth for V2 GB AEG - Rear Wired

    Brand new TITAN II Bluetooth® for V2 GB AEG is GATE flagship Electronic Trigger Unit (ETU) - Expert version

    Built-in Bluetooth 5.2 technology gives you direct access to TITAN settings, AEG telemetry and ability to use smartwatch, STATUS and other future devices of GATE Ecosystem. Innovative gear sensor not only counts gears, but also as first in the world determines the direction of a gear rotation, offering you the most precise cycle control in AEGs. Mind-blowing optical trigger sensor allows you for setting hair trigger with ludicrous precision: 50 sensitivity levels for the first millimetre of trigger movement, keeping TITAN V2 sensor advantages. TITAN II Bluetooth® is equipped with a multifunctional port ready for connecting additional accessories such as bolt-catch, magazine sensor, tracer in hop-up chamber and others.

    What makes TITAN II Bluetooth® so special?

    • Mind-blowing trigger sensor with the TITAN V2 sensor advantages and ability to set hair trigger with ludicrous precision: even 50 sensitivity levels for the first millimeter of trigger movement
    • Brand new patented gear sensor, as first in the world, detects each tooth and the direction of gear movement what allows for extremely precise cycle control
    • Mechanical protection of trigger sensors increases reliability. A potential trigger sensors' damage is now covered by the warranty.
    • Ultra-precise telemetry measurements thanks to the new current sensor
    • Pre-cocking can be set in %
    • Built-in voltage boost converter. Trouble-free operation in low temperatures
    • Multifunctional programmable port ready for connecting:
    • Hop-up chamber to tracer and sensors
    • Bolt-catch button
    • HPA Engine (Single solenoid, dual solenoid engine you need an additional cable ,accessory sold separately)
    • Electric Magazine
    • Magazine sensor
    • Flashlight

    User-friendly GCS app for iOS, Android, macOS, Windows, watchOS, Wear OS


    TITAN II can be connected with smartwatch out-of-the-box
    Compatibility with GATE Ecosystem including GATE STATUS and future hop-up chamber with tracer

    93438.jpg?time=1675330778449


    Lowest in the market current consumption. Deep sleep mode with only 0.1 mA current consumption prevents battery discharge (3x lower consumption than in current ETUs, which already had the lowest current consumption on the market).

    Multifunctional port:

    • 2x I/O port
    • UART / I2C communication
    • Programmable power supply with eFuse
    • Current: max 5.4A peak and 1.5A constant current
    • Voltage: same as battery voltage

    93439.jpg?time=1675330942483

    Compatible accesories :

    • Power supply cable (GEL BLASTER / Electric Magazine / Tracer)
    • Cable for single solenoid HPA
    • Cables for dual solenoid HPA
    • Divider ready for connecting many accessories (you can connect 1x power supply cable and 2x I/O cable)
    • Universal I/O cable for max. 2 DIY accessories (Bolt-catch, Magazine sensor, Flashlight)
    • Bolt-catch with button and cable (ready to connect)
    • Magazine sensor with cable (ready to connect)

    The kit contains:

    • 1 x TITAN II Bluetooth Mosfet - T-dean
    • 1 x Installation Kit
    • 1 x patch Gate Titan II

    The version of the TITAN II Gate AEG mosfet can be converted for a version working in HPA which would control 1 or 2 soleinoid like the Jack or Polarstar F2, Wolverine Inferno.. (accessory sold separately)

    116,58 €
    GATE TITAN II Expert version Bluetooth for V2 GB AEG - Rear Wired

    116,58 €
  • TITAN V2 EXPERT Set rear

    TITAN V2 Advanced Set is an AEG Control System for V2 gearboxes which will transform your airsoft gun into an advanced training weapon. Adjust your AEG and check the Statistics using USB-Link and GATE Control Station app for PC and Android devices. TITAN V2 enables you to adjust the trigger sensitivity with military precision. The innovative proximity trigger sensor offers you even 250 possible sensitivity settings. Gain a tactical advantage thanks to the extremely fast trigger response and many other useful functions.

    Advanced Set:

    The best for those who like complex solutions. Advanced version with wide variety of functions. It enables access to the Statistics and TITAN World Rankings.

    TITAN gives you the option to adjust:

    • Trigger sensitivity
    • Pre-cocking boost
    • Fire selector mode
    • Burst mode
    • Rate of fire
    • Low battery warning
    • Battery protection
    • Sniper delay

      TITAN has no less than eight sensors!

    • 1 gear sensor
    • 2 selector sensors
    • 5 trigger sensors

      Thanks to the gear sensor you get:
    • Automatic BURST - there is no need to set burst time. You can set burst between two and 10 shots;
    • Automatic PRE-COCKING - Pre-cocking is fully operational in SEMI, BURST and AUTO mode and there is no need to set pre-cocking boost manually. You can easily set the pre-cocking as high, mid or low;
    • FULL CYCLE - when the precocking is off, TITAN ensures that the gearbox always makes full cycles.

      You can trust TITAN because:

    • Every time you pull the trigger gearbox completes the correct cycle. The gears stop exactly where they should. The gearbox works efficiently.
    • It is protected against short-circuits, overheating and overloading
    • It protects the battery against over-discharge
    • It significantly improves battery life, rate of fire, spring life and gearbox reliability (when pre-cocking is off)
    • It is compatible with the strongest AEG replicas and batteries (ready to use with LiPo 14.8V, 5000 mAh, 60C)

      Why TITAN is so special?
    • It has a user-friendly configuration via the Tactical Programming Card and/or GATE Control Station
    • It has option to make firmware updates via the internet
    • It has innovative optical sensors instead of mechanical switches that can be prone to faults
    • It replicates a trigger response like in a real gun
    • It replaces the cut-off lever
    • It is compatible with DSG and SSG gears
    • It is compatible with most v2 gearboxes (including cnc) on the market without any modification

      Kit contents:
      TITAN Drop-in Version 2 Module
      USB-Link
      USB Cables
      Installation Kit
      Quickstart Guides

      Here's a link to its manual which is available in English, Spanish, French, Italian and Polish:

      https://www.gatee.eu/manuals

    Warning : In case of issue with the product assembled by yourself, manufacturer warranty policy will apply directly, there will be no direct  exchange or refund.

    133,25 €
    TITAN V2 EXPERT Set rear

    133,25 €

This part will be assembled and tested

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

  • Maple Leaf Macaron Hop Up Rubber 50 Degree for AEG

    Hop-up, (High Operation Power Up), is basically describes the back spin trajectory of an BB pellets, by adjusting the Hop-Up to increase their range and accuracy. As the pellet shoots through this hop up bucking, the friction creates the spin, it tends to roll and backspin.

    The Maple Leaf hop up has been adjusted to the specified degree so it solely depends on what the player needs. The "concave" shape bucking, it will provide you the best hop up effect ever and is made specifically for all AEGs out there.

    7,42 €
    Maple Leaf Macaron Hop Up Rubber 50 Degree for AEG

    7,42 €
  • Maple Leaf Macaron Hop Up Rubber 60 Degree for AEG

    Hop-up, (High Operation Power Up), is basically describes the back spin trajectory of an BB pellets, by adjusting the Hop-Up to increase their range and accuracy. As the pellet shoots through this hop up bucking, the friction creates the spin, it tends to roll and backspin.

    The Maple Leaf hop up has been adjusted to the specified degree so it solely depends on what the player needs. The "concave" shape bucking, it will provide you the best hop up effect ever and is made specifically for all AEGs out there.

    7,42 €
    Maple Leaf Macaron Hop Up Rubber 60 Degree for AEG

    7,42 €
  • Maple Leaf Macaron Hop Up Rubber 70 Degree for AEG

    Hop-up, (High Operation Power Up), is basically describes the back spin trajectory of an BB pellets, by adjusting the Hop-Up to increase their range and accuracy. As the pellet shoots through this hop up bucking, the friction creates the spin, it tends to roll and backspin.

    The Maple Leaf hop up has been adjusted to the specified degree so it solely depends on what the player needs. The "concave" shape bucking, it will provide you the best hop up effect ever and is made specifically for all AEGs out there.

    7,42 €
    Maple Leaf Macaron Hop Up Rubber 70 Degree for AEG

    7,42 €
  • Maple Leaf Macaron Hop Up Rubber 75 Degree for AEG

    Hop-up, (High Operation Power Up), is basically describes the back spin trajectory of an BB pellets, by adjusting the Hop-Up to increase their range and accuracy. As the pellet shoots through this hop up bucking, the friction creates the spin, it tends to roll and backspin.

    The Maple Leaf hop up has been adjusted to the specified degree so it solely depends on what the player needs. The "concave" shape bucking, it will provide you the best hop up effect ever and is made specifically for all AEGs out there.

    7,42 €
    Maple Leaf Macaron Hop Up Rubber 75 Degree for AEG

    7,42 €
  • Maple Leaf MR Hop Up Rubber for AEG - 50 Degree

    Maple Leaf l MR "Maximum Range" rubber is designed to improve the performance and the range of your airsoft replica.

    • For AEG airsoft barrel
    • Larger & wider contact patch for better hop effect with heavy BB's
    • The design in the shape like a "shield" ensures better support of the hop up with the support levers
    • The shield-shaped groove design has a better jump effect when the tensioner / lever presses it

    Product include 1X Maple Leaf MR Hop Up Rubber for AEG - 50 Degree (green)

    8,25 €
    Maple Leaf MR Hop Up Rubber for AEG - 50 Degree

    8,25 €
  • Maple Leaf MR Hop Up Rubber for AEG - 60 Degree

    Maple Leaf l MR "Maximum Range" rubber is designed to improve the performance and the range of your airsoft replica.

    • For AEG airsoft barrel
    • Larger & wider contact patch for better hop effect with heavy BB's
    • The design in the shape like a "shield" ensures better support of the hop up with the support levers
    • The shield-shaped groove design has a better jump effect when the tensioner / lever presses it

    Product include 1X Maple Leaf MR Hop Up Rubber for AEG - 60 Degree (yellow)

    8,25 €
    Maple Leaf MR Hop Up Rubber for AEG - 60 Degree

    8,25 €
  • Maple Leaf MR Hop Up Rubber for AEG - 70 Degree

    Maple Leaf l MR "Maximum Range" rubber is designed to improve the performance and the range of your airsoft replica.

    • For AEG airsoft barrel
    • Larger & wider contact patch for better hop effect with heavy BB's
    • The design in the shape like a "shield" ensures better support of the hop up with the support levers
    • The shield-shaped groove design has a better jump effect when the tensioner / lever presses it

    Product include 1X Maple Leaf MR Hop Up Rubber for AEG - 70 Degree (blue)

    8,25 €
    Maple Leaf MR Hop Up Rubber for AEG - 70 Degree

    8,25 €
  • Maple Leaf MR Hop Up Rubber for AEG - 75 Degree

    Maple Leaf l MR "Maximum Range" rubber is designed to improve the performance and the range of your airsoft replica.

    • For AEG airsoft barrel
    • Larger & wider contact patch for better hop effect with heavy BB's
    • The design in the shape like a "shield" ensures better support of the hop up with the support levers
    • The shield-shaped groove design has a better jump effect when the tensioner / lever presses it

    Product include 1X Maple Leaf MR Hop Up Rubber for AEG - 75 Degree (pink)

    8,25 €
    Maple Leaf MR Hop Up Rubber for AEG - 75 Degree

    8,25 €
  • Prometheus Air Seal Chamber Hop-Up Packing (Soft Type)

    If your hop-up adjustment is not having a big effect on the hop-up of your BBs, then it probably means that your hop-up packing is worn down and is not gripping the BB properly before it is fired out. A new hop-up packing will allow more accurate hop-up adjustments. Tested and approved by RedWolf. Best used on guns that shoot below 400fps.

    10,75 €
    Prometheus Air Seal Chamber Hop-Up Packing (Soft Type)

    10,75 €
  • Modify Flat Hop Up Bucking baton RYUSOKU - Hard Type

    The Modify BATON RYUSOKU Flat Hop Up Bucking is designed for stabilizing the hop when using 0.25 BBs or more

    • Friendly use
    • Efficiently improves the accuracy.
    • Stabilize and extend the trajectory
    12,42 €
    Modify Flat Hop Up Bucking baton RYUSOKU - Hard Type

    12,42 €
  • Modify Flat Hop Up Bucking baton RYUSOKU - Soft Type

    The Modify BATON RYUSOKU Flat Hop Up Bucking is designed for stabilizing the hop when using 0.2 BBs

    • Friendly use
    • Efficiently improves the accuracy.
    • Stabilize and extend the trajectory
    11,58 €
    Modify Flat Hop Up Bucking baton RYUSOKU - Soft Type

    11,58 €
  • Maple Leaf Super Macaron Hop Up Rubber 50 Degree for AEG

    Maple Leaf Super Macaron is aspecial developed bucking to be used in your AEG or SRS replica. This bucking is designed to adapt the maple leaf crazy jet barrels, which are considered VSR/GBB cut barrels, to be used in AEG hop-up systems.  While AEG buckings typically require "windowed" or "bridged" barrels, the Maple Leaf Super Macaron series slide onto "open cut/bridgeless" barrels just as a VSR style bucking would, but with the appropriate outer diameter to accommodate AEG Hop-up chambers.  The bucking is best used in conjunction with the Omega Hop-up Tensioner , and Crazy Jet Barrel to really maximize your range and rein in that left and right shot deviation!


    This bucking will fit bridged as well as bridgeless barrels, so be sure that your hop up chamber is designed for AEG buckings before ordering, as most GBB/VSR guns are designed for the thicker GBB/VSR buckings.

    • Optimal inner and outer Sealing
    • Accuracy and Range Improvement
    • Easy to install
    • Fits AEG Bridged Barrels
    • Fits GBB / VSR Unbridged Barrel

    Different degrees available for your setup, higher FPS rifles would like to use harder ones. However with colder weather you might want to step down 5 degree to avoid a stiff bucking. Harder buckings wear down less then the softer ones. Softer ones give more consistency in your shots but wear down quicker.

    The degrees of the buckings

    The degrees of the hop-up buckings mark their compatibility with guns of different muzzle energies or power levels. In general, you could say: the more powerful the gun, the higher the degree. The manufacturer recommends choosing the degree of your bucking as follows:

    Degree and color  /  Recommended power range :
    • 50 : Less than 110 m/s (1.2 J)
    • 60 : 90-120 m/s (0.8-1.5 J)
    • 70 : 110-140 m/s (1.2-2 J)
    • 75 : 130-150 m/s (1.7-2.25 J)
    • 80 : over 150 m/s (2.25 J)

    The compatibility of the bucking

    The Maple Leaf Macaron hop-up bucking is compatible with electric guns made with Tokyo Marui standards. Note, however, that the nub of the bucking is shaped a bit different, which means that the hop-up window of the inner barrel should be at least the size of the nub, which is around 4 mm or longer.

    8,25 €
    Maple Leaf Super Macaron Hop Up Rubber 50 Degree for AEG

    8,25 €
  • Maple Leaf Super Macaron Hop Up Rubber 60 Degree for AEG

    Maple Leaf Super Macaron is a special developed bucking to be used in your AEG or SRS replica. This bucking is designed to adapt the maple leaf crazy jet barrels, which are considered VSR/GBB cut barrels, to be used in AEG hop-up systems.  While AEG buckings typically require "windowed" or "bridged" barrels, the Maple Leaf Super Macaron series slide onto "open cut/bridgeless" barrels just as a VSR style bucking would, but with the appropriate outer diameter to accommodate AEG Hop-up chambers.  The bucking is best used in conjunction with the Omega Hop-up Tensioner , and Crazy Jet Barrel to really maximize your range and rein in that left and right shot deviation!


    This bucking will fit bridged as well as bridgeless barrels, so be sure that your hop up chamber is designed for AEG buckings before ordering, as most GBB/VSR guns are designed for the thicker GBB/VSR buckings.

    • Optimal inner and outer Sealing
    • Accuracy and Range Improvement
    • Easy to install
    • Fits AEG Bridged Barrels
    • Fits GBB / VSR Unbridged Barrel

    Different degrees available for your setup, higher FPS rifles would like to use harder ones. However with colder weather you might want to step down 5 degree to avoid a stiff bucking. Harder buckings wear down less then the softer ones. Softer ones give more consistency in your shots but wear down quicker.

    The degrees of the buckings

    The degrees of the hop-up buckings mark their compatibility with guns of different muzzle energies or power levels. In general, you could say: the more powerful the gun, the higher the degree. The manufacturer recommends choosing the degree of your bucking as follows:

    Degree and color  /  Recommended power range :
    • 50 : Less than 110 m/s (1.2 J)
    • 60 : 90-120 m/s (0.8-1.5 J)
    • 70 : 110-140 m/s (1.2-2 J)
    • 75 : 130-150 m/s (1.7-2.25 J)
    • 80 : over 150 m/s (2.25 J)
    The compatibility of the bucking

    The Maple Leaf Macaron hop-up bucking is compatible with electric guns made with Tokyo Marui standards. Note, however, that the nub of the bucking is shaped a bit different, which means that the hop-up window of the inner barrel should be at least the size of the nub, which is around 4 mm or longer.

    8,25 €
    Maple Leaf Super Macaron Hop Up Rubber 60 Degree for AEG

    8,25 €
  • Maple Leaf Super Macaron Hop Up Rubber 70 Degree for AEG

    Maple Leaf Super Macaron is a special developed bucking to be used in your AEG or SRS replica. This bucking is designed to adapt the maple leaf crazy jet barrels, which are considered VSR/GBB cut barrels, to be used in AEG hop-up systems.  While AEG buckings typically require "windowed" or "bridged" barrels, the Maple Leaf Super Macaron series slide onto "open cut/bridgeless" barrels just as a VSR style bucking would, but with the appropriate outer diameter to accommodate AEG Hop-up chambers.  The bucking is best used in conjunction with the Omega Hop-up Tensioner , and Crazy Jet Barrel to really maximize your range and rein in that left and right shot deviation!


    This bucking will fit bridged as well as bridgeless barrels, so be sure that your hop up chamber is designed for AEG buckings before ordering, as most GBB/VSR guns are designed for the thicker GBB/VSR buckings.

    • Optimal inner and outer Sealing
    • Accuracy and Range Improvement
    • Easy to install
    • Fits AEG Bridged Barrels
    • Fits GBB / VSR Unbridged Barrel

    Different degrees available for your setup, higher FPS rifles would like to use harder ones. However with colder weather you might want to step down 5 degree to avoid a stiff bucking. Harder buckings wear down less then the softer ones. Softer ones give more consistency in your shots but wear down quicker.

    The degrees of the buckings

    The degrees of the hop-up buckings mark their compatibility with guns of different muzzle energies or power levels. In general, you could say: the more powerful the gun, the higher the degree. The manufacturer recommends choosing the degree of your bucking as follows:

    Degree and color  /  Recommended power range :
    • 50 : Less than 110 m/s (1.2 J)
    • 60 : 90-120 m/s (0.8-1.5 J)
    • 70 : 110-140 m/s (1.2-2 J)
    • 75 : 130-150 m/s (1.7-2.25 J)
    • 80 : over 150 m/s (2.25 J)
    The compatibility of the bucking

    The Maple Leaf Macaron hop-up bucking is compatible with electric guns made with Tokyo Marui standards. Note, however, that the nub of the bucking is shaped a bit different, which means that the hop-up window of the inner barrel should be at least the size of the nub, which is around 4 mm or longer.

    8,25 €
    Maple Leaf Super Macaron Hop Up Rubber 70 Degree for AEG

    8,25 €
  • Maple Leaf Super Macaron Hop Up Rubber 75 Degree for AEG

    Maple Leaf Super Macaron is a special developed bucking to be used in your AEG or SRS replica. This bucking is designed to adapt the maple leaf crazy jet barrels, which are considered VSR/GBB cut barrels, to be used in AEG hop-up systems.  While AEG buckings typically require "windowed" or "bridged" barrels, the Maple Leaf Super Macaron series slide onto "open cut/bridgeless" barrels just as a VSR style bucking would, but with the appropriate outer diameter to accommodate AEG Hop-up chambers.  The bucking is best used in conjunction with the Omega Hop-up Tensioner , and Crazy Jet Barrel to really maximize your range and rein in that left and right shot deviation!


    This bucking will fit bridged as well as bridgeless barrels, so be sure that your hop up chamber is designed for AEG buckings before ordering, as most GBB/VSR guns are designed for the thicker GBB/VSR buckings.

    • Optimal inner and outer Sealing
    • Accuracy and Range Improvement
    • Easy to install
    • Fits AEG Bridged Barrels
    • Fits GBB / VSR Unbridged Barrel

    Different degrees available for your setup, higher FPS rifles would like to use harder ones. However with colder weather you might want to step down 5 degree to avoid a stiff bucking. Harder buckings wear down less then the softer ones. Softer ones give more consistency in your shots but wear down quicker.

    The degrees of the buckings

    The degrees of the hop-up buckings mark their compatibility with guns of different muzzle energies or power levels. In general, you could say: the more powerful the gun, the higher the degree. The manufacturer recommends choosing the degree of your bucking as follows:

    Degree and color  /  Recommended power range :
    • 50 : Less than 110 m/s (1.2 J)
    • 60 : 90-120 m/s (0.8-1.5 J)
    • 70 : 110-140 m/s (1.2-2 J)
    • 75 : 130-150 m/s (1.7-2.25 J)
    • 80 : over 150 m/s (2.25 J)
    The compatibility of the bucking

    The Maple Leaf Macaron hop-up bucking is compatible with electric guns made with Tokyo Marui standards. Note, however, that the nub of the bucking is shaped a bit different, which means that the hop-up window of the inner barrel should be at least the size of the nub, which is around 4 mm or longer.

    8,25 €
    Maple Leaf Super Macaron Hop Up Rubber 75 Degree for AEG

    8,25 €

This part will be assembled and tested with your custom replica

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

  • T238 speed Tunable Trigger Archer for M4 AEG - Black

    • CNC aluminum alloy material, anodized surface
    • With multiple adjustment points, you can adjust pre-travel and over-travel of the trigger
    • Independent steel shaft, more wear-resistant and smoother
    • Suitable for V2 M4 gearbox AEG / HPA USE
    19,92 €
    T238 speed Tunable Trigger Archer for M4 AEG - Black

    19,92 €
  • T238 speed Tunable Trigger Archer for M4 AEG - Orange

    • CNC aluminum alloy material, anodized surface
    • With multiple adjustment points, you can adjust pre-travel and over-travel of the trigger
    • Independent steel shaft, more wear-resistant and smoother
    • Suitable for V2 M4 gearbox AEG / HPA USE
    19,92 €
    T238 speed Tunable Trigger Archer for M4 AEG - Orange

    19,92 €
  • T238 speed Tunable Trigger Archer for M4 AEG - Red

    • CNC aluminum alloy material, anodized surface
    • With multiple adjustment points, you can adjust pre-travel and over-travel of the trigger
    • Independent steel shaft, more wear-resistant and smoother
    • Suitable for V2 M4 gearbox AEG / HPA USE
    19,92 €
    T238 speed Tunable Trigger Archer for M4 AEG - Red

    19,92 €
  • T238 speed Tunable Trigger Blade for M4 AEG - Black

    • CNC aluminum alloy material, anodized surface
    • With multiple adjustment points, you can adjust pre-travel and over-travel of the trigger
    • Independent steel shaft, more wear-resistant and smoother
    • Suitable for V2 M4 gearbox AEG / HPA USE
    13,25 €
    T238 speed Tunable Trigger Blade for M4 AEG - Black

    13,25 €
  • T238 speed Tunable Trigger Blade for M4 AEG - Silver

    • CNC aluminum alloy material, anodized surface
    • With multiple adjustment points, you can adjust pre-travel and over-travel of the trigger
    • Independent steel shaft, more wear-resistant and smoother
    • Suitable for V2 M4 gearbox AEG / HPA USE
    13,25 €
    T238 speed Tunable Trigger Blade for M4 AEG - Silver

    13,25 €
  • T238 speed Tunable Trigger Blade for M4 AEG - Red

    • CNC aluminum alloy material, anodized surface
    • With multiple adjustment points, you can adjust pre-travel and over-travel of the trigger
    • Independent steel shaft, more wear-resistant and smoother
    • Suitable for V2 M4 gearbox AEG / HPA USE
    13,25 €
    T238 speed Tunable Trigger Blade for M4 AEG - Red

    13,25 €
  • Maxx Model CNC Advanced Speed Trigger Style A

    CNC Aluminum Advanced Speed Trigger is specially designed for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles. The Advanced Speed Trigger has multiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards. The Advanced Speed Trigger is completely compatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box.

    The Advanced Speed Trigger is designed with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems. The main pivot pin of the trigger is made from Titanium for maximum strength and durability. The body of the trigger is CNC machined out of a solid block of Aircraft Grade Aluminum. The Aluminum and Titanium construction makes this trigger very light and durable. Moreover, the trigger is carefully chamfered the edges and securely fitted with three rubber pads to ensure comfort, enhance traction and secure grip. With the unique shapes, stylish design and colors, we will have an option to fit your style needs.

     Includes
    product_right_arrow.png1 x CNC Aluminum Advanced Speed Trigger
    product_right_arrow.png2 x Setscrew
    product_right_arrow.png3 x Rubber Pad
    product_right_arrow.png1 x Titanium Pivot Pin
    product_right_arrow.png1 x Steel Trigger Spring

     

     Specification
    product_right_arrow.pngOverall Length: 47.75mm
    product_right_arrow.pngOverall Width: 7mm
    product_right_arrow.pngPivot Pin Diameter: 3mm
    product_right_arrow.pngMaterial: Titanium /Aluminum 6061

     

     Features
    product_right_arrow.pngMachined from a solid block of Aircraft Grade Aluminum with tight tolerances to provide better accuracy, consistency, and durability
    product_right_arrow.pngDesigned for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles
    product_right_arrow.pngMultiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards
    product_right_arrow.pngCompatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box
    product_right_arrow.pngDesigned with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems
    product_right_arrow.pngTitanium Pivot Pin for maximum strength and durability
    product_right_arrow.pngAluminum and Titanium construction, very light and durable
    product_right_arrow.pngChamfered the edges and fitted with three rubber pads to ensure comfort, enhance traction and secure grip
    product_right_arrow.pngUnique shapes, stylish design and colors

     

     Usage
    product_right_arrow.pngUsed for Ver. 2 gear box AEG/HPA (M4, M16,...)

     

     Requires
    product_right_arrow.pngWearing eye protection is recommended
    product_right_arrow.pngUse proper tools for disassembly and reassembly the gear box with great care due to spring tension
    product_right_arrow.pngBearing lubricant oil/grease is recommended for smooth operation

     

     Instruction
    product_right_arrow.pngInstruction Manuals are included
    24,16 €
    Maxx Model CNC Advanced Speed Trigger Style A

    24,16 €
  • Maxx Model CNC Advanced Speed Trigger Style B

    CNC Aluminum Advanced Speed Trigger is specially designed for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles. The Advanced Speed Trigger has multiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards. The Advanced Speed Trigger is completely compatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box.

    The Advanced Speed Trigger is designed with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems. The main pivot pin of the trigger is made from Titanium for maximum strength and durability. The body of the trigger is CNC machined out of a solid block of Aircraft Grade Aluminum. The Aluminum and Titanium construction makes this trigger very light and durable. Moreover, the trigger is carefully chamfered the edges and securely fitted with three rubber pads to ensure comfort, enhance traction and secure grip. With the unique shapes, stylish design and colors, we will have an option to fit your style needs.

     Includes
    product_right_arrow.png1 x CNC Aluminum Advanced Speed Trigger
    product_right_arrow.png2 x Setscrew
    product_right_arrow.png3 x Rubber Pad
    product_right_arrow.png1 x Titanium Pivot Pin
    product_right_arrow.png1 x Steel Trigger Spring

     

     Specification
    product_right_arrow.pngOverall Length: 47.75mm
    product_right_arrow.pngOverall Width: 7mm
    product_right_arrow.pngPivot Pin Diameter: 3mm
    product_right_arrow.pngMaterial: Titanium /Aluminum 6061

     

     Features
    product_right_arrow.pngMachined from a solid block of Aircraft Grade Aluminum with tight tolerances to provide better accuracy, consistency, and durability
    product_right_arrow.pngDesigned for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles
    product_right_arrow.pngMultiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards
    product_right_arrow.pngCompatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box
    product_right_arrow.pngDesigned with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems
    product_right_arrow.pngTitanium Pivot Pin for maximum strength and durability
    product_right_arrow.pngAluminum and Titanium construction, very light and durable
    product_right_arrow.pngChamfered the edges and fitted with three rubber pads to ensure comfort, enhance traction and secure grip
    product_right_arrow.pngUnique shapes, stylish design and colors

     

     Usage
    product_right_arrow.pngUsed for Ver. 2 gear box AEG/HPA (M4, M16,...)

     

     Requires
    product_right_arrow.pngWearing eye protection is recommended
    product_right_arrow.pngUse proper tools for disassembly and reassembly the gear box with great care due to spring tension
    product_right_arrow.pngBearing lubricant oil/grease is recommended for smooth operation

     

     Instruction
    product_right_arrow.pngInstruction Manuals are included
    24,16 €
    Maxx Model CNC Advanced Speed Trigger Style B

    24,16 €
  • Maxx Model CNC Advanced Speed Trigger Style C

    CNC Aluminum Advanced Speed Trigger is specially designed for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles. The Advanced Speed Trigger has multiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards. The Advanced Speed Trigger is completely compatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box.

    The Advanced Speed Trigger is designed with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems. The main pivot pin of the trigger is made from Titanium for maximum strength and durability. The body of the trigger is CNC machined out of a solid block of Aircraft Grade Aluminum. The Aluminum and Titanium construction makes this trigger very light and durable. Moreover, the trigger is carefully chamfered the edges and securely fitted with three rubber pads to ensure comfort, enhance traction and secure grip. With the unique shapes, stylish design and colors, we will have an option to fit your style needs.

     Includes
    product_right_arrow.png1 x CNC Aluminum Advanced Speed Trigger
    product_right_arrow.png2 x Setscrew
    product_right_arrow.png3 x Rubber Pad
    product_right_arrow.png1 x Titanium Pivot Pin
    product_right_arrow.png1 x Steel Trigger Spring

     

     Specification
    product_right_arrow.pngOverall Length: 47.75mm
    product_right_arrow.pngOverall Width: 7mm
    product_right_arrow.pngPivot Pin Diameter: 3mm
    product_right_arrow.pngMaterial: Titanium /Aluminum 6061

     

     Features
    product_right_arrow.pngMachined from a solid block of Aircraft Grade Aluminum with tight tolerances to provide better accuracy, consistency, and durability
    product_right_arrow.pngDesigned for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles
    product_right_arrow.pngMultiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards
    product_right_arrow.pngCompatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box
    product_right_arrow.pngDesigned with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems
    product_right_arrow.pngTitanium Pivot Pin for maximum strength and durability
    product_right_arrow.pngAluminum and Titanium construction, very light and durable
    product_right_arrow.pngChamfered the edges and fitted with three rubber pads to ensure comfort, enhance traction and secure grip
    product_right_arrow.pngUnique shapes, stylish design and colors

     

     Usage
    product_right_arrow.pngUsed for Ver. 2 gear box AEG/HPA (M4, M16,...)

     

     Requires
    product_right_arrow.pngWearing eye protection is recommended
    product_right_arrow.pngUse proper tools for disassembly and reassembly the gear box with great care due to spring tension
    product_right_arrow.pngBearing lubricant oil/grease is recommended for smooth operation

     

     Instruction
    product_right_arrow.pngInstruction Manuals are included
    24,16 €
    Maxx Model CNC Advanced Speed Trigger Style C

    24,16 €
  • Maxx Model CNC Advanced Speed Trigger Style D

    CNC Aluminum Advanced Speed Trigger is specially designed for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles. The Advanced Speed Trigger has multiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards. The Advanced Speed Trigger is completely compatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box.

    The Advanced Speed Trigger is designed with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems. The main pivot pin of the trigger is made from Titanium for maximum strength and durability. The body of the trigger is CNC machined out of a solid block of Aircraft Grade Aluminum. The Aluminum and Titanium construction makes this trigger very light and durable. Moreover, the trigger is carefully chamfered the edges and securely fitted with three rubber pads to ensure comfort, enhance traction and secure grip. With the unique shapes, stylish design and colors, we will have an option to fit your style needs.

     Includes
    product_right_arrow.png1 x CNC Aluminum Advanced Speed Trigger
    product_right_arrow.png2 x Setscrew
    product_right_arrow.png3 x Rubber Pad
    product_right_arrow.png1 x Titanium Pivot Pin
    product_right_arrow.png1 x Steel Trigger Spring

     

     Specification
    product_right_arrow.pngOverall Length: 47.75mm
    product_right_arrow.pngOverall Width: 7mm
    product_right_arrow.pngPivot Pin Diameter: 3mm
    product_right_arrow.pngMaterial: Titanium /Aluminum 6061

     

     Features
    product_right_arrow.pngMachined from a solid block of Aircraft Grade Aluminum with tight tolerances to provide better accuracy, consistency, and durability
    product_right_arrow.pngDesigned for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles
    product_right_arrow.pngMultiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards
    product_right_arrow.pngCompatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box
    product_right_arrow.pngDesigned with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems
    product_right_arrow.pngTitanium Pivot Pin for maximum strength and durability
    product_right_arrow.pngAluminum and Titanium construction, very light and durable
    product_right_arrow.pngChamfered the edges and fitted with three rubber pads to ensure comfort, enhance traction and secure grip
    product_right_arrow.pngUnique shapes, stylish design and colors

     

     Usage
    product_right_arrow.pngUsed for Ver. 2 gear box AEG/HPA (M4, M16,...)

     

     Requires
    product_right_arrow.pngWearing eye protection is recommended
    product_right_arrow.pngUse proper tools for disassembly and reassembly the gear box with great care due to spring tension
    product_right_arrow.pngBearing lubricant oil/grease is recommended for smooth operation

     

     Instruction
    product_right_arrow.pngInstruction Manuals are included
    24,16 €
    Maxx Model CNC Advanced Speed Trigger Style D

    24,16 €
  • Maxx Model CNC Advanced Speed Trigger Style E

    CNC Aluminum Advanced Speed Trigger is specially designed for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles. The Advanced Speed Trigger has multiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards. The Advanced Speed Trigger is completely compatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box.

    The Advanced Speed Trigger is designed with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems. The main pivot pin of the trigger is made from Titanium for maximum strength and durability. The body of the trigger is CNC machined out of a solid block of Aircraft Grade Aluminum. The Aluminum and Titanium construction makes this trigger very light and durable. Moreover, the trigger is carefully chamfered the edges and securely fitted with three rubber pads to ensure comfort, enhance traction and secure grip. With the unique shapes, stylish design and colors, we will have an option to fit your style needs.

     Includes
    product_right_arrow.png1 x CNC Aluminum Advanced Speed Trigger
    product_right_arrow.png2 x Setscrew
    product_right_arrow.png3 x Rubber Pad
    product_right_arrow.png1 x Titanium Pivot Pin
    product_right_arrow.png1 x Steel Trigger Spring

     

     Specification
    product_right_arrow.pngOverall Length: 47.75mm
    product_right_arrow.pngOverall Width: 7mm
    product_right_arrow.pngPivot Pin Diameter: 3mm
    product_right_arrow.pngMaterial: Titanium /Aluminum 6061

     

     Features
    product_right_arrow.pngMachined from a solid block of Aircraft Grade Aluminum with tight tolerances to provide better accuracy, consistency, and durability
    product_right_arrow.pngDesigned for fast response, smooth and consistent trigger pull on Ver. 2 Gear Box of M4/M16 series Airsoft AEG Rifles
    product_right_arrow.pngMultiple adjustment points to control pre-travel and over-travel to shorten trigger pull and prevent damage to electronic switches on controller boards
    product_right_arrow.pngCompatible with the popular TITAN™ Electronic Module from Gate for Ver. 2 Gear Box
    product_right_arrow.pngDesigned with relieve cuts to function in most Tokyo Marui (TM) spec. AEG and HPA systems
    product_right_arrow.pngTitanium Pivot Pin for maximum strength and durability
    product_right_arrow.pngAluminum and Titanium construction, very light and durable
    product_right_arrow.pngChamfered the edges and fitted with three rubber pads to ensure comfort, enhance traction and secure grip
    product_right_arrow.pngUnique shapes, stylish design and colors

     

     Usage
    product_right_arrow.pngUsed for Ver. 2 gear box AEG/HPA (M4, M16,...)

     

     Requires
    product_right_arrow.pngWearing eye protection is recommended
    product_right_arrow.pngUse proper tools for disassembly and reassembly the gear box with great care due to spring tension
    product_right_arrow.pngBearing lubricant oil/grease is recommended for smooth operation

     

     Instruction
    product_right_arrow.pngInstruction Manuals are included
    24,16 €
    Maxx Model CNC Advanced Speed Trigger Style E

    24,16 €
  • Gate 2B1 NOVA Trigger V2 M4

    • TITAN V2 Compatible
    • AEG V2 TM spec compatible
    • HPA V2 Tm spec compatible

    An adjustable speed trigger designed especially for pros using TITAN V2 for the greatest accuracy and overcoming limits. Enjoy simple and precise hair-trigger adjustment on any sensor you want. Shoot faster thanks to over-travel control. Make the most of the compatibility with any gearbox wherever standard V2 trigger fits, including HPA. Select from multiple shapes and colors to suit the style and type of your games. All of this with ultra-high quality of 7075 aircraft grade aluminum CNC machining.

    Features:

    • Designed especially for TITAN V2
    • Pre-travel screw - hair-trigger adjustment
    • Over-travel screw - limit trigger movement from outside the rifle body and shoot faster
    • Long-Lok system against loose screws
    • Full compatibility with TITAN V2 allowing the use of all 5 sensors
    • Full compatibility with HPA engines and standard V2 trigger contacts
    • Multiple shapes and colors to suit the style and type of your games
    • Ultra-high quality of aircraft-grade aluminum CNC machining
    • No modification of AEG required
    • Compatibility with ASTER V2 as a standard trigger*
    • Dedicated especially to pros and skilled users

    Compatibility:

    • All standard V2 gearboxes like Tokyo Marui
    • TITAN V2
    • Standard trigger contacts like Tokyo Marui
    • HPA engines

    Love the TITAN hair-trigger, but need exact adjustments? Thanks to the pre-travel and over-travel screws, you can exactly set the point where the trigger starts its movement and how far you can pull it.

    Enter the world of full control. Use the first trigger ever especially designed for the TITAN V2 ETU. Make no compromises and utilize full trigger range from the very first sensor. Need hair-trigger in exact position? Thanks to the adjustment points you can set the movement e.g. on the third sensor and the movement range to just two millimeters. The Nova Trigger makes adjustments easy and precise. No need for changes in ETU position or grinding the body of your replica. Just install the trigger, set the limits of the travel or even hair-trigger, and you are ready.

    We know that style is important. You’re no longer limited to the few shapes of adjustable triggers on the market. Enjoy the full range of designs and colors, both classic and futuristic.

    Need a new high-end trigger for your HPA build or standard trigger contacts? Nova is the answer. Enjoy the ultra-high quality of CNC aluminum machining and 7 different colors to fit your replica.

    24,92 €
    Gate 2B1 NOVA Trigger V2 M4

    24,92 €
  • Gate 2C1 NOVA Trigger V2 M4

    • TITAN V2 Compatible
    • AEG V2 TM spec compatible
    • HPA V2 Tm spec compatible

    An adjustable speed trigger designed especially for pros using TITAN V2 for the greatest accuracy and overcoming limits. Enjoy simple and precise hair-trigger adjustment on any sensor you want. Shoot faster thanks to over-travel control. Make the most of the compatibility with any gearbox wherever standard V2 trigger fits, including HPA. Select from multiple shapes and colors to suit the style and type of your games. All of this with ultra-high quality of 7075 aircraft grade aluminum CNC machining.

    Features:

    • Designed especially for TITAN V2
    • Pre-travel screw - hair-trigger adjustment
    • Over-travel screw - limit trigger movement from outside the rifle body and shoot faster
    • Long-Lok system against loose screws
    • Full compatibility with TITAN V2 allowing the use of all 5 sensors
    • Full compatibility with HPA engines and standard V2 trigger contacts
    • Multiple shapes and colors to suit the style and type of your games
    • Ultra-high quality of aircraft-grade aluminum CNC machining
    • No modification of AEG required
    • Compatibility with ASTER V2 as a standard trigger*
    • Dedicated especially to pros and skilled users

    Compatibility:

    • All standard V2 gearboxes like Tokyo Marui
    • TITAN V2
    • Standard trigger contacts like Tokyo Marui
    • HPA engines

    Love the TITAN hair-trigger, but need exact adjustments? Thanks to the pre-travel and over-travel screws, you can exactly set the point where the trigger starts its movement and how far you can pull it.

    Enter the world of full control. Use the first trigger ever especially designed for the TITAN V2 ETU. Make no compromises and utilize full trigger range from the very first sensor. Need hair-trigger in exact position? Thanks to the adjustment points you can set the movement e.g. on the third sensor and the movement range to just two millimeters. The Nova Trigger makes adjustments easy and precise. No need for changes in ETU position or grinding the body of your replica. Just install the trigger, set the limits of the travel or even hair-trigger, and you are ready.

    We know that style is important. You’re no longer limited to the few shapes of adjustable triggers on the market. Enjoy the full range of designs and colors, both classic and futuristic.

    Need a new high-end trigger for your HPA build or standard trigger contacts? Nova is the answer. Enjoy the ultra-high quality of CNC aluminum machining and 7 different colors to fit your replica.

    24,92 €
    Gate 2C1 NOVA Trigger V2 M4

    24,92 €
  • Gate 2E1 NOVA Trigger V2 M4

    • TITAN V2 Compatible
    • AEG V2 TM spec compatible
    • HPA V2 Tm spec compatible

    An adjustable speed trigger designed especially for pros using TITAN V2 for the greatest accuracy and overcoming limits. Enjoy simple and precise hair-trigger adjustment on any sensor you want. Shoot faster thanks to over-travel control. Make the most of the compatibility with any gearbox wherever standard V2 trigger fits, including HPA. Select from multiple shapes and colors to suit the style and type of your games. All of this with ultra-high quality of 7075 aircraft grade aluminum CNC machining.

    Features:

    • Designed especially for TITAN V2
    • Pre-travel screw - hair-trigger adjustment
    • Over-travel screw - limit trigger movement from outside the rifle body and shoot faster
    • Long-Lok system against loose screws
    • Full compatibility with TITAN V2 allowing the use of all 5 sensors
    • Full compatibility with HPA engines and standard V2 trigger contacts
    • Multiple shapes and colors to suit the style and type of your games
    • Ultra-high quality of aircraft-grade aluminum CNC machining
    • No modification of AEG required
    • Dedicated especially to pros and skilled users

    Compatibility:

    • All standard V2 gearboxes like Tokyo Marui
    • TITAN V2
    • Standard trigger contacts like Tokyo Marui
    • HPA engines

    Love the TITAN hair-trigger, but need exact adjustments? Thanks to the pre-travel and over-travel screws, you can exactly set the point where the trigger starts its movement and how far you can pull it.

    Enter the world of full control. Use the first trigger ever especially designed for the TITAN V2 ETU. Make no compromises and utilize full trigger range from the very first sensor. Need hair-trigger in exact position? Thanks to the adjustment points you can set the movement e.g. on the third sensor and the movement range to just two millimeters. The Nova Trigger makes adjustments easy and precise. No need for changes in ETU position or grinding the body of your replica. Just install the trigger, set the limits of the travel or even hair-trigger, and you are ready.

    We know that style is important. You’re no longer limited to the few shapes of adjustable triggers on the market. Enjoy the full range of designs and colors, both classic and futuristic.

    Need a new high-end trigger for your HPA build or standard trigger contacts? Nova is the answer. Enjoy the ultra-high quality of CNC aluminum machining and 7 different colors to fit your replica.

    24,92 €
    Gate 2E1 NOVA Trigger V2 M4

    24,92 €
  • Gate Quantum Trigger 1B1 for ASTER

    When hair trigger starts to be boring, it means you are ready for the next level. With Quantum Trigger and ASTER V2, you can set sensitivity from ludicrous ‘touch’ through ‘hair’ to full movement. Using the Quantum Trigger, you benefit from a totally new way of trigger detection. Instead of covering, the trigger precisely reflects the light. Shape and surface of the QT is unique and dedicated to work with ASTER V2 sensor. This CNC Quantum Trigger is like a diamond among coal rocks. Dare to try it. All these features give that extreme resolution.

    Features:

    • Ultra-high resolution – even 60 trigger sensitivities for the 1st mm (0.04 in) of movement
    • Even 470 possible sensitivity levels for whole movement
    • Designed to work with ASTER V2 optical sensors
    • Dedicated especially for pros and skilled users
    • Made from aluminium by CNC

    Compatible only with ASTER V2.

    Notice: Quantum Trigger requires at least GCS 3.0 beta 5 (Windows/macOS) or GCS 1.5.6 (Android devices) and ASTER firmware version 3.1-03 or later.

    22,42 €
    Gate Quantum Trigger 1B1 for ASTER

    22,42 €
  • Gate Quantum Trigger 1C1 for ASTER

    When hair trigger starts to be boring, it means you are ready for the next level. With Quantum Trigger and ASTER V2, you can set sensitivity from ludicrous ‘touch’ through ‘hair’ to full movement. Using the Quantum Trigger, you benefit from a totally new way of trigger detection. Instead of covering, the trigger precisely reflects the light. Shape and surface of the QT is unique and dedicated to work with ASTER V2 sensor. This CNC Quantum Trigger is like a diamond among coal rocks. Dare to try it. All these features give that extreme resolution.

    Features:

    • Ultra-high resolution – even 60 trigger sensitivities for the 1st mm (0.04 in) of movement
    • Even 470 possible sensitivity levels for whole movement
    • Designed to work with ASTER V2 optical sensors
    • Dedicated especially for pros and skilled users
    • Made from aluminium by CNC

    Compatible only with ASTER V2.

    Notice: Quantum Trigger requires at least GCS 3.0 beta 5 (Windows/macOS) or GCS 1.5.6 (Android devices) and ASTER firmware version 3.1-03 or later.

    22,42 €
    Gate Quantum Trigger 1C1 for ASTER

    22,42 €
  • Gate Quantum Trigger 1E1 for ASTER

    When hair trigger starts to be boring, it means you are ready for the next level. With Quantum Trigger and ASTER V2, you can set sensitivity from ludicrous ‘touch’ through ‘hair’ to full movement. Using the Quantum Trigger, you benefit from a totally new way of trigger detection. Instead of covering, the trigger precisely reflects the light. Shape and surface of the QT is unique and dedicated to work with ASTER V2 sensor. This CNC Quantum Trigger is like a diamond among coal rocks. Dare to try it. All these features give that extreme resolution.

    Features:

    • Ultra-high resolution – even 60 trigger sensitivities for the 1st mm (0.04 in) of movement
    • Even 470 possible sensitivity levels for whole movement
    • Designed to work with ASTER V2 optical sensors
    • Dedicated especially for pros and skilled users
    • Made from aluminium by CNC

    Compatible only with ASTER V2.

    Notice: Quantum Trigger requires at least GCS 3.0 beta 5 (Windows/macOS) or GCS 1.5.6 (Android devices) and ASTER firmware version 3.1-03 or later.

    22,42 €
    Gate Quantum Trigger 1E1 for ASTER

    22,42 €

This part will be assembled and tested with your custom replica

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

  • Option No.1 Motor Brushless Hi-torque long plug-in

    The OptionNo.1 brand unveilsa brand new Hi-torque Long Brushless motor that will allow you to upgrade your AEG replica. The special features of the Brushless motor allow you to benefit from impressive performance while reducing electrical consumption and removing the constraints of a conventional carbon motor.

    This motor is suitable for all mosfets! * see table below

    option-no1-moteur-brushless-hi-torque-lo

    • Increased response time compared to a conventional engine
    • Power consumption down
    • Operation by magnetic field
    • No motor brushes
    • Heats much less than a conventional engine
    • More torque
    • No mechanical and electrical loss
    • High performance
    • Plug-in design simple to install
    • 7.4V 31000 rpm LiPo battery
    • LiPo 11.1v 46000 rpm battery
    • Low voltage protection
    • Overheating protection
    • 100 Protection temperature protection

    option_003_d2.jpg

    92,01 €

    Remises par quantités

    QuantityPrixÉconomie
    1 78,21 € au moins 13,80 €
    Option No.1 Motor Brushless Hi-torque long plug-in

    92,01 €
  • Guarder Infinite Torque-Up motor - Long Type

    Guarder Infinite Torque-Up Type Motor

    Two Ball Bearing Bushing Inside
    Aluminum Axis Bushing.
    Guarder Motor Pinion Gear (Thermal Treatment)

    49,08 €
    Guarder Infinite Torque-Up motor - Long Type

    49,08 €
  • Nimrod NT Blackbird 20K CNC Motor long axis

    The Blackbird 20K series is built with solid materials and is suitable for every setup. Due to the high TPA (Turns Per Armature) it can easily pull up all of springs available for AEGs. Our magnets can withstand high temperatures up to 150°C and the armature is equipped with a cooling system as well as 0.8mm wires. The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.

    • U/min @ 11.1V: 20000
    • TPA: 26
    • Pinion Gear Shape: D-Shape

    We do recommend using it in the following setups

    • Gearset : 18:1 / 16:1 / 13:1 / 12:1
    • Springs : all
    58,25 €
    Nimrod NT Blackbird 20K CNC Motor long axis

    58,25 €
  • Nimrod NT Blackbird 26K CNC Motor Long axis

    The Blackbird 26K series is built with solid materials and is suitable for nearly every setup. Due to the high TPA (Turns Per Armature) it can easily pull up all kinds of springs available for AEGs. Our magnets can withstand high temperatures up to 150°C and the armature is equipped with a cooling system as well as 0.8mm wires. The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.

    • U/min @ 11.1V: 26000
    • TPA: 19
    • Pinion Gear Shape: D-Shape

    We do recommend using it in the following setups

    • Gearset : 32:1 / 18:1 / 16:1 / 13:1 / 12:1
    • Springs : M110+
    59,08 €
    Nimrod NT Blackbird 26K CNC Motor Long axis

    59,08 €
  • Nimrod NT Blackbird 30K CNC Motor long axis

    The Blackbird 30K series is built with solid materials and is suitable for nearly every setup. Due to the high TPA (Turns Per Armature) it can easily pull up most of of springs available for AEGs. Our magnets can withstand high temperatures up to 150°C and the armature is equipped with a cooling system as well as 0.8mm wires. The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.

    • U/min @ 11.1V: 30000
    • TPA: 16
    • Pinion Gear Shape: D-Shape

    We do recommend using it in the following setups

    • Gearset : 32:1 / 18:1 / 16:1 / 13:1
    • Springs : M100-M150
    59,08 €
    Nimrod NT Blackbird 30K CNC Motor long axis

    59,08 €
  • Nimrod NT Blackbird 39K CNC Motor long axis

    The Blackbird 39K series is built with solid materials and is suitable for nearly every setup. Due to the high rpm, it also can be used in short stroked 0.5 Joules or under 1 Joule builds. Take care of the spring and sector gear management to prevent a pre interlocking which will cause a broken piston or sector gear. Our magnets can withstand high temperatures up to 150°C and the armature is equipped with a cooling system as well as 0.8mm wires. The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.

    • U/min @ 11.1V: 39000
    • TPA: 14
    • Pinion Gear Shape: D-Shape

    We do recommend using it in the following setups

    • Gearset : 32:1 / 18:1 / 16:1
    • Springs : M100 to M140
    58,25 €
    Nimrod NT Blackbird 39K CNC Motor long axis

    58,25 €
  • Nimrod NT Blackbird 45K CNC Motor Long axis

    The Blackbird 45K series is built with solid materials and is suitable for nearly every setup. Due to the high rpm, it also can be used in short stroked 0.5 Joules or under 1 Joule builds. Take care of the spring and sector gear management to prevent a pre interlocking which will cause a broken piston or sector gear. Our magnets can withstand high temperatures up to 150°C and the armature is equipped with a cooling system as well as 0.8mm wires. The cooling port near the end bell does provide impactful cooling without risking damaging the motor if any internals fail. The CNC machined end bell also does provide better cooling and better fit and endurance of the bearings inside the motor. The pinion gear is made of strong MIM technology material and with D-shape fitting, it is easy to change if you need to. It also provides a better force translation than O-shaped pinion gears.

    • U/min @ 11.1V: 45000
    • TPA: 11
    • Pinion Gear Shape: D-Shape

    We do recommend using it in the following setups

    • 32:1 / 18:1
    • Springs: M100 to M130
    59,08 €
    Nimrod NT Blackbird 45K CNC Motor Long axis

    59,08 €
  • Nimrod NT Blackbird 36K/27K CNC Brushless Motor long

    The Nimrod Tactical Brushless motor has 2 adjustable speed settings. Depending on the battery being used, either 27000 rpm or 36000 rpm can be set. Same as with the regular Nimrod motors, a D-shape pinion gear is used. Thus the power transmission is better and the change of the bevel gear is easier. The motor should only be used in conjunction with strong batteries. The C rating must necessarily be above 40 / 60. Also, the battery should have a high capacity (1400 mAh or more) to operate smoothly. The motor has been successfully tested with a variety of mosfets available on the market and it can be reported that all tested combinations worked well together.

    Please note that some Mosfet manufacturers cannot guarantee that operation with a brushless motor is possible. In this regard, always refer to the Mosfet manufacturer’s specifications. To ensure a trouble-free installation, the pinion to bevel gear position must be considered. Some grips and motor covers need to be modified to allow a perfect fit of the motor.

    149,92 €
    Nimrod NT Blackbird 36K/27K CNC Brushless Motor long

    149,92 €
  • Point ultra torque motor axe long

    Precisely made engine type ULTRA TORQUE, thanks to the use of ball bearings and strong neodymium magnets can handle even the hardest springs. The motor axis is type D and the motor gear is secured by a screw. Suitable for Version 2 AEG

    38,25 €
    Point ultra torque motor axe long

    38,25 €
  • SHS high torque motor long axis

    The SHS high-torque motor is an affordable, high quality AEG motor that has been enhanced for high torque output. Well known from every gunsmith for several years, it is an essential base for upgrading your replica, especially since its price / performance ratio is unbeatable.

    Features :

    • Steel pinion gear
    • Neodym magnets
    • 16 TPA
    • Excellent ROF and responsiveness
    • Long axis version



    29,08 €
    SHS high torque motor long axis

    29,08 €
  • T238 33000 rpm Brushless Motor long axis

    T238 High Thermal Efficiency Brushless Motor, High Torque, High Speed, Overheat Low voltage Locked Rotor Protection, Stepless Speed Regulation Long Axis Airsoft AEG Motor.

    Feature:

    • Motor body material: CNC Aluminum precision machining
    • Motor gear: D type
    • Brushless, low heat at high output
    • Long service life, battery temperature
    • Emergency stop after power failure, no buffer, stable output
    • Overheat protection, low voltage protection, locked rotor protection
    • Stepless speed regulation (range 50-100%) can be adjusted through the potentiometer of the small hole in the tail cover.
    • This brushless motor is best to use with our own brand ETU/MOSFET

    Specification:

    • Maximum power: 380W
    • Input voltage: 7.4-16.8V
    • 11.1V voltage state
    • Speed: 33000rpm

    Compatibility :

    • Long Axis fits for M4/M16/MP5/G3/P90 series and other long type motor Airsoft AEG

    Package including:

    • 1 X brushless motor
    • 1 X screwdriver

    108,25 €
    T238 33000 rpm Brushless Motor long axis

    108,25 €
  • T238 39000 rpm Brushless Motor long axis

    T238 High Thermal Efficiency Brushless Motor, High Torque, High Speed, Overheat Low voltage Locked Rotor Protection, Stepless Speed Regulation Long Axis Airsoft AEG Motor.

    Feature:

    • Motor body material: CNC Aluminum precision machining
    • Motor gear: D type
    • Brushless, low heat at high output
    • Long service life, battery temperature
    • Emergency stop after power failure, no buffer, stable output
    • Overheat protection, low voltage protection, locked rotor protection
    • Stepless speed regulation (range 50-100%) can be adjusted through the potentiometer of the small hole in the tail cover.
    • This brushless motor is best to use with our own brand ETU/MOSFET

    Specification:

    • Maximum power: 380W
    • Input voltage: 7.4-16.8V
    • 11.1V voltage state
    • Speed: 39000rpm

    Compatibility :

    • Long Axis fits for M4/M16/MP5/G3/P90 series and other long type motor Airsoft AEG

    Package including:

    • 1 X brushless motor
    • 1 X screwdriver
    108,25 €
    T238 39000 rpm Brushless Motor long axis

    108,25 €
  • T238 High-torque Motor N35 18TPA

    T238 High-speed / High-torque Motor N35 18TPA High Thermal Efficiency Motor Longt Axe 480 Motor for Airsoft V2 Gearbox

    Feature :

    • Newest design
    • Rotor active cooling fan
    • full CNC metal shell
    • high temperature resistant 180 degree magnetic tile,
    • enlarged rotor,
    • high-precision commutator,
    • Japanese wear-resistant new material carbon brush.

    Compatibility :

    • Long Axis fits for M4/M16/MP5/G3/P90 series and other long type motor Airsoft AEG

    Specification:

    No load :

    • Speed: 33000rpm
    • Current: 3.6A

    Load:

    • Speed: 28500rpm
    • Current: 18.5A
    • Torque: 503g-cm
    • For TPA: 18TPA
    • For magnets: N35
    47,42 €
    T238 High-torque Motor N35 18TPA

    47,42 €
  • G&G Talaria 40K Motor Long Axis

    • High-Performance Motor
    • Compatible to up to 12v Batteries
    • Designed for AEG
    • Shaft: Long
    • Magnets: Neodymium
    • Maximum speed: 40000rpm
    83,25 €
    G&G Talaria 40K Motor Long Axis

    83,25 €
  • Warhead BASE Brushless motor 27K long axis

    Brushless DC motors represent a huge technological breakthrough. The efficiency of brushless motors is significantly higher than the efficiency and performance of efficiency brushed motors.

    • Die-cast aluminum housing
    • Totally customized design with maximum power and torque
    • High temperature resistant copper winding by PLC
    • SH quality magnets
    • Internal ESC with over-current and low-voltage cut-off to protect motor and battery.
    • High quality "D" insert for motor gear
    • Compatibility: AEG using long ax motors

    Information: 27,000 rpm in 11.1 v Lipo

    Operating voltage: 7.2v - 11.4v (2S to 3S Lipo battery)

    69434.jpg?time=1638183335142

    120,75 €
    Warhead BASE Brushless motor 27K long axis

    120,75 €
  • Warhead Motor Brushless STANDARD 30K long axis

    Brushless DC motors represent a huge technological leap forward. The efficiency of brushless motors is significantly higher than the efficiency and performance of brushless motors.

    • High quality 7075 aluminum housing
    • Totally customized design with maximum power and torque
    • High temperature resistant quality copper winding
    • High quality magnets
    • Internal ESC with over-current and low-voltage cut-off to protect motor and battery.
    • High precision CNC design
    • High quality "D" insert for motor gear
    • Compatibility: AEG using short axis motors

    Information: 20,000 rpm in 7.4 v Lipo - 30,000 rpm in 11.1 v Lipo

    Operating voltage: 7.2v - 11.4v (2S to 3S Lipo battery)

    69434.jpg?time=1638183335142

    153,25 €
    Warhead Motor Brushless STANDARD 30K long axis

    153,25 €
  • Warhead BASE Brushless motor 35K long axis

    Brushless DC motors represent a huge technological breakthrough. The efficiency of brushless motors is significantly higher than the efficiency and performance of efficiency brushed motors.

    • Die-cast aluminum housing
    • Totally customized design with maximum power and torque
    • High temperature resistant copper winding by PLC
    • SH quality magnets
    • Internal ESC with over-current and low-voltage cut-off to protect motor and battery.
    • High quality "D" insert for motor gear
    • Compatibility: AEG using long ax motors

    Information: 35,000 rpm in 11.1 v Lipo

    Operating voltage: 7.2v - 11.4v (2S to 3S Lipo battery)

    69434.jpg?time=1638183335142

    124,92 €
    Warhead BASE Brushless motor 35K long axis

    124,92 €
  • Warhead Motor Brushless HIGH speed 36K long axis

    Brushless DC motors represent a huge technological leap forward. The efficiency of brushless motors is significantly higher than the efficiency and performance of brushless motors.

    • High quality 7075 aluminum housing
    • Totally customized design with maximum power and torque
    • High temperature resistant quality copper winding
    • High quality magnets
    • Internal ESC with over-current and low-voltage cut-off to protect motor and battery.
    • High precision CNC design
    • High quality "D" insert for motor gear
    • Compatibility: AEG using short axis motors

    Information: 25,000 rpm in 7.4 v Lipo - 36,000 rpm in 11.1 v Lipo

    Operating voltage: 7.2v - 11.4v (2S to 3S Lipo battery)

    69434.jpg?time=1638183335142

    149,92 €
    Warhead Motor Brushless HIGH speed 36K long axis

    149,92 €
  • Warhead BASE Brushless motor 45K long axis

    Brushless DC motors represent a huge technological breakthrough. The efficiency of brushless motors is significantly higher than the efficiency and performance of efficiency brushed motors.

    • Die-cast aluminum housing
    • Totally customized design with maximum power and torque
    • High temperature resistant copper winding by PLC
    • SH quality magnets
    • Internal ESC with over-current and low-voltage cut-off to protect motor and battery.
    • High quality "D" insert for motor gear
    • Compatibility: AEG using long ax motors

    Information: 45,000 rpm in 11.1 v Lipo

    Operating voltage: 7.2v - 11.4v (2S to 3S Lipo battery)

    69434.jpg?time=1638183335142

    120,75 €
    Warhead BASE Brushless motor 45K long axis

    120,75 €
  • Warhead Brushless Motor ULTRAHIGH speed 52K long axis

    Brushless DC motors represent a huge technological leap forward. The efficiency of brushless motors is significantly higher than the efficiency and performance of brushless motors.

    • High quality 7075 aluminum housing
    • Totally customized design with maximum power and torque
    • High temperature resistant quality copper winding
    • High quality magnets
    • Internal ESC with over-current and low-voltage cut-off to protect motor and battery.
    • High precision CNC design
    • High quality "D" insert for motor gear
    • Compatibility: AEG using short axis motors

    Information: 35,000 rpm in 7.4 v Lipo - 52,000 rpm in 11.1 v Lipo

    Operating voltage: 7.2v - 11.4v (2S to 3S Lipo battery)

    69434.jpg?time=1638183335142

    149,92 €
    Warhead Brushless Motor ULTRAHIGH speed 52K long axis

    149,92 €

This part will be assembled and tested

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

  • Maxx Model CNC Hopup Chamber M4A PRO for M4 AEG

    CNC Aluminum Hopup Chamber M4A Pro (with BB Latching System) unit is precisely machined to perform accurately and consistently on Tokyo Marui (include G&G, KRYTAC, except KWA) Standard M4/M16 AEG series. The Hopup Chamber M4A unit is built with an aluminum Rotary Dial Knob for fine hopup adjustments, the precision Hopup Lever and 4mm Bucking Nubs (6mm Bucking Nubs are optional) to perform best with R-Hop and Standard-Hop to keep the BB shooting accurately and consistently on every single shot.

    The Hopup Chamber M4A unit is designed to accept 21.00mm to 21.25mm nozzle length, and fully compatible with most aftermarket soft and hard rubber buckings without losing FPS or dropping BB during use. The Hopup Chamber M4A unit is wisely equipped with an interchangeable Inlet Adaptor OD11mm to ensure the hopup unit is inserted exactly in the center of the 11mm inner bore AEG Gearbox/HPA Engine nozzle outlet without wobbling. (Inlet Adaptor OD11.5mm and OD12mm are optional)
    Also mounted the removable CNC Brass Side Wings to slide smoothly into the outer barrel slots, and included an advanced CNC Delrin Locking C-Clip to hold the inner barrel tight in place without wobbling and twisting.

    More than that, the Hopup Chamber M4A Pro unit is specially designed with a new BB Latching System to prevent BB dropping after removing the magazine. The Latching Arm can also be manually pressed to release the remaining BB from inside the hopup chamber.

    ***The Dual UV LED Tracer Module is an add-on option to glow BB in the dark. Operating Voltage from 7VDC - 15VDC (2-4 cells LiPo, 6-13 cells NiCad). (Sold separately)
    ***Test results: FPS might be increased from 10FPS to 30FPS over the stock setup. Please check your FPS!

     

     Includes
    product_right_arrow.png1 x CNC Aluminum Hopup Chamber M4A Pro (with BB Latching System) unit
    product_right_arrow.png2 x CNC Acrylic Side Cover
    product_right_arrow.png2 x CNC Brass 2.5mm Side Wing
    product_right_arrow.png1 x CNC Steel Pivot Pin
    product_right_arrow.png1 x CNC Aluminum Hopup Lever
    product_right_arrow.png1 x CNC Aluminum Soft Round Nub
    product_right_arrow.png1 x CNC Aluminum Soft Flat Nub (4mm)
    product_right_arrow.png1 x CNC Aluminum Hard Concave Nub (4mm)
    product_right_arrow.png3 x Steel Nub Spring
    product_right_arrow.png1 x CNC Steel Spring Guide
    product_right_arrow.png1 x Steel Upper Compression Spring
    product_right_arrow.png1 x Steel Center Compression Spring
    product_right_arrow.png1 x CNC Delrin Locking C-Clip
    product_right_arrow.png1 x CNC Brass Barrel Spacer
    product_right_arrow.png1 x Brass Barrel Spacer Holder Oring
    product_right_arrow.png1 x CNC Aluminum Rotary Dial Knob
    product_right_arrow.png1 x CNC Aluminum Inlet Adaptor (OD11mm)
    product_right_arrow.png1 x CNC Brass Inlet Spacer

     

     Specification
    product_right_arrow.pngOverall Length: 51.65mm
    product_right_arrow.pngOverall Height: 37.75mm
    product_right_arrow.pngInlet Adaptor Outer Diameter (to fit into Gear Box): 11mm
    product_right_arrow.pngHub Outer Diameter (to fit into Outer Barrel): 12mm
    product_right_arrow.pngHub Inner Diameter (to fit Nozzle): 8mm
    product_right_arrow.pngFeeder Outer Diameter (to fit magazine): 8.85mm
    product_right_arrow.pngFeeder Length (to fit magazine): 6mm
    product_right_arrow.pngMaterial: Aluminum 6061

     

     Features
    product_right_arrow.pngMachined from a solid aircraft aluminum block with tight tolerances to achieve the most accuracy, consistency, and durability
    product_right_arrow.pngPerformed accurately and consistently on Tokyo Marui (include G&G, KRYTAC, except KWA) Standard M4/M16 AEG series
    product_right_arrow.pngPrecision Rotary Dial Knob for fine hopup adjustments
    product_right_arrow.pngRe-engineered the precision Hopup Lever and 4mm Bucking Nubs (6mm Bucking Nubs are optional) to perform best with R-Hop and Standard-Hop to keep the BB shooting accurately and consistently on every single shot
    product_right_arrow.pngRemovable Steel Pivot Pin for ease of setup and maintenance
    product_right_arrow.pngAccepted 21.00mm to 21.25mm nozzle length
    product_right_arrow.pngFully compatible with most aftermarket soft and hard rubber buckings without losing FPS or dropping BB during use
    product_right_arrow.pngWisely equipped with an interchangeable Inlet Adaptor OD11mm to ensure the hopup unit is inserted exactly in the center of the 11mm inner bore AEG Gearbox/HPA Engine nozzle outlet without wobbling. (Inlet Adaptor OD11.5mm and OD12mm are sold separately)
    product_right_arrow.pngMounted the removable CNC Brass Side Wings to slide smoothly into the outer barrel slots
    product_right_arrow.pngIncluded an advanced CNC Delrin Locking C-Clip to hold the inner barrel tight in place without wobbling and twisting
    product_right_arrow.pngEquipped with 2 compression springs on top and center to ensure the hopup unit is seated straight and air tight during use
    product_right_arrow.pngSpecially designed with a new BB Latching System to prevent BB dropping after removing the magazine
    product_right_arrow.pngThe Latching Arm can also be manually pressed to release the remaining BB from inside the hopup chamber
    product_right_arrow.pngCompatible with any 11mm inner bore AEG Gearbox/HPA Engine nozzle outlets
    product_right_arrow.pngThe Dual UV LED Tracer Module to glow BB in the dark ready!

     

     Weight
    product_right_arrow.pngN/A grams

     

     Usage
    product_right_arrow.pngCompatible with most Tokyo Marui (include G&G, KRYTAC, except KWA) Standard M4/M16 AEG series

     

     Requires
    product_right_arrow.pngWearing eye protection is recommended
    product_right_arrow.pngUse proper tools for disassembly and reassembly the gear box with great care due to spring tension
    product_right_arrow.pngBearing lubricant oil/grease is recommended for smooth operation

     

     Instruction
    product_right_arrow.pngInstruction Manuals are included
    52,44 €

    Remises par quantités

    QuantityPrixÉconomie
    1 36,71 € au moins 15,73 €
    Maxx Model CNC Hopup Chamber M4A PRO for M4 AEG

    52,44 €
  • Maxx Model CNC Hopup Chamber M4P PRO for Polarstar M4 HPA

    CNC Aluminum Hopup Chamber M4P Pro (with BB Latching System) unit is precisely machined to perform accurately and consistently with HPA PolarStar Engines on standard M4/M16 platform. The Hopup Chamber M4P unit is built with an aluminum Rotary Dial Knob for fine hopup adjustments, the precision Hopup Lever and 4mm Bucking Nubs (6mm Bucking Nubs are optional) to perform best with R-Hop and Standard-Hop to keep the BB shooting accurately and consistently on every single shot.
    The Hopup Chamber M4P unit is designed to accept the HPA PolarStar Engine M4 nozzle length, and fully compatible with most aftermarket soft and hard rubber buckings without losing FPS or dropping BB during use.

    The Hopup Chamber M4P unit is wisely equipped with an interchangeable Inlet Adaptor OD11mm to ensure the hopup unit is inserted exactly in the center of the 11mm inner bore HPA Engine nozzle outlet without wobbling. (Inlet Adaptor OD11.5mm and OD12mm are optional)
    Also mounted the removable CNC Brass Side Wings to slide smoothly into the outer barrel slots, and included an advanced CNC Delrin Locking C-Clip to hold the inner barrel tight in place without wobbling and twisting.

    More than that, the Hopup Chamber M4P Pro unit is specially designed with a new BB Latching System to prevent BB dropping after removing the magazine. The Latching Arm can also be manually pressed to release the remaining BB from inside the hopup chamber.

    ***The Dual UV LED Tracer Module is an add-on option to glow BB in the dark. Operating Voltage from 7VDC - 15VDC (2-4 cells LiPo, 6-13 cells NiCad). (Sold separately)
    ***Test results: FPS might be increased from 10FPS to 30FPS over the stock setup. Please check your FPS!

     

     Includes
    product_right_arrow.png1 x CNC Aluminum Hopup Chamber M4P Pro (with BB Latching System) unit
    product_right_arrow.png2 x CNC Acrylic Side Cover
    product_right_arrow.png2 x CNC Brass 2.5mm Side Wing
    product_right_arrow.png1 x CNC Steel Pivot Pin
    product_right_arrow.png1 x CNC Aluminum Hopup Lever
    product_right_arrow.png1 x CNC Aluminum Soft Round Nub
    product_right_arrow.png1 x CNC Aluminum Soft Flat Nub (4mm)
    product_right_arrow.png1 x CNC Aluminum Hard Concave Nub (4mm)
    product_right_arrow.png3 x Steel Nub Spring
    product_right_arrow.png1 x CNC Steel Spring Guide
    product_right_arrow.png1 x Steel Upper Compression Spring
    product_right_arrow.png1 x Steel Center Compression Spring
    product_right_arrow.png1 x CNC Delrin Locking C-Clip
    product_right_arrow.png1 x CNC Brass Barrel Spacer
    product_right_arrow.png1 x Brass Barrel Spacer Holder Oring
    product_right_arrow.png1 x CNC Aluminum Rotary Dial Knob
    product_right_arrow.png1 x CNC Aluminum Inlet Adaptor (OD11mm)

     

     Specification
    product_right_arrow.pngOverall Length: 51.15mm
    product_right_arrow.pngOverall Height: 37.75mm
    product_right_arrow.pngInlet Adaptor Outer Diameter (to fit into HPA Nozzle Outlet): 11mm
    product_right_arrow.pngHub Outer Diameter (to fit into Outer Barrel): 12mm
    product_right_arrow.pngHub Inner Diameter (to fit Nozzle): 8mm
    product_right_arrow.pngFeeder Outer Diameter (to fit magazine): 8.85mm
    product_right_arrow.pngFeeder Length (to fit magazine): 6mm
    product_right_arrow.pngMaterial: Aluminum 6061

     

     Features
    product_right_arrow.pngMachined from a solid aircraft aluminum block with tight tolerances to achieve the most accuracy, consistency, and durability
    product_right_arrow.pngPerformed accurately and consistently with HPA PolarStar Engines on standard M4/M16 platform
    product_right_arrow.pngPrecision Rotary Dial Knob for fine hopup adjustments
    product_right_arrow.pngRe-engineered the precision Hopup Lever and 4mm Bucking Nubs (6mm Bucking Nubs are optional) to perform best with R-Hop and Standard-Hop to keep the BB shooting accurately and consistently on every single shot
    product_right_arrow.pngRemovable Steel Pivot Pin for ease of setup and maintenance
    product_right_arrow.pngAccepted the HPA PolarStar Engine M4 nozzle length
    product_right_arrow.pngFully compatible with most aftermarket soft and hard rubber buckings without losing FPS or dropping BB during use
    product_right_arrow.pngWisely equipped with an interchangeable Inlet Adaptor OD11mm to ensure the hopup unit is inserted exactly in the center of the 11mm inner bore HPA Engine nozzle outlet without wobbling. (Inlet Adaptor OD11.5mm and OD12mm are sold separately)
    product_right_arrow.pngMounted the removable CNC Brass Side Wings to slide smoothly into the outer barrel slots
    product_right_arrow.pngIncluded an advanced CNC Delrin Locking C-Clip to hold the inner barrel tight in place without wobbling and twisting
    product_right_arrow.pngEquipped with 2 compression springs on top and center to ensure the hopup unit is seated straight and air tight during use
    product_right_arrow.pngSpecially designed with a new BB Latching System to prevent BB dropping after removing the magazine
    product_right_arrow.pngThe Latching Arm can also be manually pressed to release the remaining BB from inside the hopup chamber
    product_right_arrow.pngCompatible with any 11mm inner bore HPA Engine nozzle outlets
    product_right_arrow.pngThe Dual UV LED Tracer Module to glow BB in the dark ready!

     

     Weight
    product_right_arrow.pngN/A grams

     

     Usage
    product_right_arrow.pngCompatible with most HPA PolarStar Engines on standard M4/M16 platform

     

     Requires
    product_right_arrow.pngWearing eye protection is recommended
    product_right_arrow.pngUse proper tools for disassembly and reassembly the gear box with great care due to spring tension
    product_right_arrow.pngBearing lubricant oil/grease is recommended for smooth operation

     

     Instruction
    product_right_arrow.pngInstruction Manuals are included

    PolarStar Airsoft is a division of PolarStar Engineering & Machine (PSE&M).

    74,92 €
    Maxx Model CNC Hopup Chamber M4P PRO for Polarstar M4 HPA

    74,92 €
  • ProWin M4 Chamber for Marui AEG

    ProWin Now offers the entire hop chamber unit for your favorite M4/M16 AEG! The ProWin Brand is known to create precision complex-shaped parts with their refined CNC manufacturing methods which sets it apart from other brands cast metal method.The CNC milled hop up is made from a solid piece of stock aircraft grade aluminum which means that the material completely consistent and eliminates the possibility of bubbles and weak areas in the metal. Anodized hard treatment in cobalt blue color adds to durability and that custom look.

    Features include:

    • Full CNC and anodized blue high grade aluminum body
    • Hop up adjustable via ring for utmost stability in comparison to the gear type
    • Retaining clips and pins all designed for quick change of worn hop packing/rubber
    • Highly durable and promotes high accuracy and lasting shooting stability
    • Significantly lighter and stronger material than the traditional cast metal type hop up units

    21,58 €
    ProWin M4 Chamber for Marui AEG

    21,58 €
  • RETROARMS CNC Hop Up Chamber AR15 UNI for M4 AEG

    30,75 €
    RETROARMS CNC Hop Up Chamber AR15 UNI for M4 AEG

    30,75 €
  • Silent Industries AEG Alpha CNC hop-up chamber

    TRUE-TDC

    To get the most consistent pressure on the bucking through the hop-up settings, we had to include TDC. This means the nub can only move in up & down motion.The TDC trolley we include is made for nubs, so you can use your desired nub.We recommend using our Black Nubs, Blue Nubs, ML Omega or similar height nubs, because our system was optimised for it.Our TDC system provides the most travel distance, meaning it can lift heavy BBs easily!

    TENSIONER RING SYSTEM

    Our Revolutionary tensioner system is very easy to assemble, it utilises Tensioner rings! In the package you get two rings, black & white (extra rings can be bought for tighter settings)

    • We recommend trying ML SuperMacaron with White Ring!
    • Black is for tighter lip tension
    • White is looser lip tension

    117930.jpg?time=1709284411616

    This is the only Hop-Up chamber on the market that fully supports the bucking lips!

    ADJUSTABLE FEED TUBE

    The Adjustable Feed Tube enables you to set length of if it, meaning you can fine tune it for your magazines! This can improve the feeding  and reduce the up/down play of the magazine in the magwell. (If you have different branded magazines, try them all before use to make an universal adjustment)

    BARREL ALIGNMENT GROOVE

    The Alpha features a groove that can help you with barrel alignment, we recommend using this as a reference point as some less quality barrels can have misaligned hop-up window! We recommend Sniper Upgrades, PDI, Lambda, ZCI stainless steel barrels! They are tried and tested by us!

    117929.jpg?time=1709284411067

    GAME CHANGER FOR HPA BUILDS

    HPA engines in general have much stronger BB loading force compared to AEGs, this sometimes can lead to issues such as double feeding, mid-cap syndrome or BB placement. Our Alpha chamber with it’s innovative bucking lip tensioner system can help with these issues as you can fine tune the loading resistance! It is a highly recommended chamber for Wolverine, PolarStar, Gate Pulsar engine builds!

    Wolverine-Airsoft-Horizontal-Black.png-s    polarstar-logo.jpg

    WHAT’S INCLUDED?

    • Hop-up chamber base
    • Adjustment Wheel
    • Feed Tube
    • Hop-up arm
    • TDC nub carriage
    • Blue Nub (Extended)
    • Stainless Steel pin for the hop-up arm
    • O-rings for the Hop-Up body (2 pcs)
    • O-rings for the barrel (8 pcs)
    • C-clip
    • Barrel Stabilizer
    • 3x Shims for Nozzle Lenght Adjustment
    • 2x Bucking Lip tensioners (Black & White)

    WHAT DO YOU NEED?

    • Hop-up bucking (G&G Green, Madbull Blue/Red, Maple Leaf Super Macaron, Prometheus Purple, Begadi buckings)
    • R-hop (Optional!)
    • Tight and Very Tight tensioner rings (optional)
    • Recommended nozzle length is standard 21.2mm (can be adjusted with the included shims!)

    BRAND COMPATIBILTY

    • Krytac
    • VFC (MCX too with minor mod)
    • G&G
    • G&P
    • Cyma
    • Specna Arms
    • Novritsch SSR4
    • Lancer Tactical
    • Double Eagle

    Does NOT fit:

    • ICS
    • Novritsch SSR9 (might fit with some mods)
    74,92 €
    Silent Industries AEG Alpha CNC hop-up chamber

    74,92 €

This part will be assembled and tested with your custom replica

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

  • Lambda FIVE precision Barrel for AEG / M14 - 128mm

    Precision barrel in SUS304 stainless steel compatible with AEG M4 and M14 replicas. These guns are directly manufactured in the Osaka factory in Japan and are of very high quality. All LAMBDA guns are designed on CNC machines.

    • The FIVE range from Lambda is the most precise range in terms of finish with its 1 micron tolerance.
    • The FIVE range from Lambda is similar to the high-end PDI.
    • The internal diameter is 6.05mm
    • The external diameter is 8.55mm

    canon-de-precision-lambda-five-pour-aeg-

    30,75 €
    Lambda FIVE precision Barrel for AEG / M14 - 128mm

    30,75 €
  • Lambda SMART 6.12 precision Barrel for M4 AEG & M14 - 128mm

    • The SMART range from Lambda is the same as PDI raven (without oxyd black finish)
    • Suitable for AEG & M14
    • The internal diameter is 6.12mm
    • The external diameter is 8.55mm

    canon-de-precision-lambda-five-pour-aeg-

    17,42 €
    Lambda SMART 6.12 precision Barrel for M4 AEG & M14 - 128mm

    17,42 €
  • Prometheus EG 6.03mm precision Barrel 128mm ( Old gen )

    High grade precision barrel from Prometheus at 6.03mm diameter for extra power and precision shooting.

    With a precision barrel, you can opt for higher grade precision BB's for greater accuracy.

    49,92 €
    Prometheus EG 6.03mm precision Barrel 128mm ( Old gen )

    49,92 €

arrow_drop_downRécapitulatif :

Total :

Partagez votre création avec vos amis.

More info

Workshop preparation :

  • Open the gearbox, take off everything inside, cleaning & degreasing shells
  • Adjusting the new CNC gears with inox shims only, one by one (spring timing or other original shims are deleted)
  • Short stroke of the piston and sector gear (for speed version only)
  • Angle of engagement optimisation (AOE) for piston and cylinder bumper
  • Short trigger system modification will be fitted for maximum responsiveness
  • Greasing mecanic & pneumatic parts
  • Firing tests
Important note :
  • 12 month warranty by P6 Workshop
  • Time to build 1-4 days before shipping
  • We recommend 11.1v lipo battery (not included) adviced in "accessories" section
  • Don't feed your mid cap magazine more than 80% of the maximal capacity
  • We strongly advice you to use high performance BBs such as BLS, Krytac, Madbull ASG blaster Devil or open Blaster.
  • Never use grease or any silicone on the electric gun, magazine or BBs

Data sheet

TypeM4
Caliber6mm Airsoft
Thread type14mm CCW
Hop-upAdjustable
Power sourceElectric
GearboxV2
Gearbox inserts8mm Bearings
Gear ratioSelectable
Quick change spring GearboxNo
Integrated MosfetYes Factory built in
Trigger SystemElectronic
Motor versionLong Axis
BatteryNot Included
Battery chargerNot Included
Power (FPS @ 0.20gr)Selectable

Customization

After saving your customized product, remember to add it to your cart.

loader

* required fields

Accessories

Mosfet

Here is a sum-up list of the available mosfets for our custom AEG airsoft guns. Note that you may see or not see this options following the Custom replica.

Important note : With a high performance mosfet configuration, for each shot fired the motor is instantly launched and instantly stopped, wich mean the more you shoot fast with a lot of quantity shot in few timing, the motor is heating accordingly, this is normal, but too much is not advised. Our products are made to get a very responsive semi automatic and make short full auto. If you wish to fire a lot of BBs in during a short timing (speedQB, Machine gun), we strongly advice to get HPA system more suitable.

The best for those who prefer simplicity but require highest quality. Economic version with limited number of functions. If you will decide to have more functions, there is always option to upgrade firmware from BASIC to ADVANCED. In order to upgrade your TITAN firmware from BASIC to ADVANCED, you need to purchase the upgrade Economic version with limited number of functions.

 VIDEO

TITAN V2 Advanced Set is an AEG Control System for V2 gearboxes which will transform your airsoft gun into an advanced training weapon. Adjust your AEG and check the Statistics using USB-Link and GATE Control Station app for PC and Android devices. TITAN V2 enables you to adjust the trigger sensitivity with military precision. The innovative proximity trigger sensor offers you even 250 possible sensitivity settings. Gain a tactical advantage thanks to the extremely fast trigger response and many other useful functions.

 VIDEO

Leviathan - V2 is processor controlled mosfet with Bluetooth communication. It adds new shooting modes, controls RoF, pre-cocking, active braking, low battery indication, statistics... Everything is controlled via application in the smart phone (iOS and Android). Device is fully integrated inside the gearbox version 2 instead of the original trigger contacts. Comes with completely made wires to stock with 30A mini fuse and deanT connector - no soldering needed.

VIDEO 

This option feature a modified Gate TITAN module combined with ICFU System (Integrated Custom Firestop Upgrade) : the system makes stop firing the replica when there is no BB left in the magazine, just like a PTW !

  • Stop BBs when magazine is empty
  • Gate Titan integrated mosfet
  • No bolt stop system necessary to resume fire
  • ICFU requires special magazine, not possible to use regular M4 AEG Magazine
  • Please never update the Firware, that would delete the ICFU fonction permently

 VIDEO ICFU Magazine

This option feature a modified Jefftron Leviathan module combined with ICFU System (Integrated Custom Firestop Upgrade) : the system makes stop firing the replica when there is no BB left in the magazine, just like a PTW !

  • Stop BBs when magazine is empty
  • Jefftron Leviathan integrated mosfet
  • No bolt stop system necessary to resume fire
  • ICFU requires special magazine, not possible to use regular M4 AEG Magazine
  • Please never update the Firware, that would delete the ICFU fonction permently

 VIDEO  ICFU Magazine

Airsoft gun Law

This airsoft replica is subject to the french Decree No. 99-240 of March 24, 1999, which regulates the law of replica firearms developing an output energy from the muzzle greater than 0.08 joule and equal to or less than 2 joules. This product is intended for recreational use only. By adding this product to your cart, you acknowledge:

  • Being older than 18
  • Master the basic safety rules concerning the use of this type of replica (wearing protective glasses, playing in a suitable and private place, etc.).
  • Never expose the replica in a public place because it can be mistaken for a real weapon with all the disastrous consequences that this implies
  • Being in full knowledge of the airsoft laws in your local country and buying knowingly, Powair6 cannot be responsible in the case of illegal importation.
  • Never point or shoot at a person, animal or any other object representing any danger.
  • Do not aim with your replica until you are ready to shoot at the target you have selected.
  • Do not shoot on a hard surface, risk of the ball bouncing, or in water, which could cause dangerous ricochets.
  • Do not aim the shot at the eyes or ears.
  • Do not use airsoft without wearing goggles or a protective mask.
  • Do not attempt to modify or disassemble the product in order to increase its firing power. It can be dangerous and will void the warranty.
  • Always be sure to keep the safety “ON” when you are no longer using the product.
  • Never look into the barrel, a BB may be hurt your eyes.

Questions  (1)

A partir de Mike | 2022-12-09 22:58:47

Bonjours,
Et-il possible d'ajouter sur le Custom le
Fraisage du RIS pour accueillir le silencieux AAC HIVE à l'achat d'une Arp556
Cordialement

Powair6

Bonjour;
oui il sera possible de le rajouter, n'hésitez pas à nous envoyer un mail (info@powair6.com) avant de passer votre commande afin que l'on puisse vous rajouter la main-d'oeuvre.
Cordialement.

Page: 1
Seuls les utilisateurs enregistrés peuvent poser une question. Login