Powair6 si proud to introduce the CYMA CM097 series with HPA system fitted. It will be delivered with the following features :
Important note :
The new Cyma 097 series airsoft assault rifle are produced in different specification that includes civil or military. The lower receiver, the upper receiver, the stock tube, the external barrel, the fire selector, the magazine release button, the trigger, the charging handle, and the front and rear sight are made in aluminum, that made the replica is more realistic. Each model has on the lower receiver a unique serial number.
The rifle in the new E-EDITION & HIGH-SPEED configuration has a velocity of around 360 fps and, in combination with a LiPo battery, a ROF around 25rps and a faster trigger response. This was achieved due to the new gearbox parts with increased durability, such as:
Set include :
|Firing mode||Semi - Full auto|
|Thread type||14mm counterclockwise (CCW)|
|Length||810 / 890mm|
|Outer Barrel lenght||14.5 inch|
|Inner barrel (mm)||370|
|Inner Barrel dia (mm)||6.03|
|Gearbox inserts||8mm Bearings|
|Gear ratio||Super high Speed 13:1|
|Quick change spring||Yes|
|Integrated Mosfet||Yes Factory built in|
|Motor||V2 Long Axis|
|Magazine Version||Mid cap spring operated|
|Battery charger||Not Included|
|Battery Connector||Small Tamiya|
|Power (FPS @ 0.20gr)||360|
No reviews at this time.
The Redline SR-E Lightning is a Patent Pending HPA drop in cylinder replacement. The Lightning is not just another cylinder replacement engine. It uses only a single solenoid, has a forward biased nozzle and fires from a true closed bolt. Due to its true closed bolt design the Lightning is much more consistent in seating the BB in the bucking from shot to shot when compared to a typical open bolt HPA engine. The result is more consistent shot to shot velocity, tighter groupings and greater accuracy at range when compared to open bolt HPA engines. A unique feature of the Lightning is that it uses a mechanically sealed, dump chamber. Rather than relying on solenoid dwell to control the volume of air used to propel the BB, the Lightning fills an internal air chamber at the pressure set by the users external supply regulator. When fired, this air chamber is mechanically sealed off from the supply and the chambers contents is released down the barrel to propel the BB. This feature contributes to the Lightnings excellent shot to shot consistency, with no air wasted do to improper dwell settings. The Lightning is also super simple to set up. Since there is no poppet dwell to tune you just set your supply regulators output pressure to match the Joules required and you are good to go. The proper amount of air needed for each shot regardless of BB weight, barrel length or any other factor is all that is released.
The Hurricane is the flagship of our new SR line of engines. The SR-M Hurricane is an evolution of the now famous N7 Milsim. Both engines being semi only, closed bolt mechanical- pneumatic drop-in HPA engines. Although the Hurricane shares no parts with the N7 Milsim. The Hurricane does have the same outstanding performance and reliability that N7 Milsim owners have come know and love, with the added benefit of increased air efficiency. The fact that the Hurricane is mechanical-pneumatic means that there is no battery or FCU needed. Just plug in your regulated air source and you are good to go. That also means that even rain and snow are not a worry since there are no electronics to short or corrode. Due to its true closed bolt design, the Hurricane is much more consistent in seating the BB in the bucking from shot to shot. When compared to typical open bolt HPA engines, the result is more consistent shot to shot velocity, tighter groupings and greater accuracy at range.A unique feature of the Hurricane is that it uses a mechanically sealed, dump chamber. Rather than relying on solenoid dwell to control the volume of air used to propel the BB, the Hurricane fills an internal chamber at the pressure set by the users external supply regulator. When fired, this air chamber is mechanically sealed off from the supply and the chambers contents released down the barrel to propel the BB. This feature contributes to the Hurricane’s excellent shot to shot consistency, with no air wasted do to improper dwell settings. The Hurricane is also super simple to set up. Since there is no FCU to tune, you just set your supply regulators output pressure to match the Joules required and you are good to go. The proper amount of air needed for each shot regardless of BB weight, barrel length or any other factor is all that is released. Please note that the N7 Hurricane is not compatible with ICFU and Custom trigger with shortened course, do not choose those options if you want an N7 Milsim
F2 is essentially a Mini Fusion Engine. It offers the same adjustability and performance as the Fusion Engine in a cylinder sized package. Patented Dual Solenoid Design : The dual solenoid design of the F2™ provides the same functionality as the legendary Fusion Engine™ but in a more compact, efficient and flexible design. Dual solenoids allow for the nozzle and the poppet valve to be adjusted independently of each other for unparalleled control over both the loading time and air volume used. Additionally, this makes it possible to change the firing sequence giving it the ability to operate in both true closed bolt as well as "AEG" mode. Increased Efficiency : The F2™ incorporates a new one-piece, lightweight poppet valve design yet still operates on the same principle as the Fusion Engine™ poppet. This valve is able to operate at lower pressures and uses less air volume to function which optimizes air efficiency. The standard F2 poppet is equivilent to the Red Low-Flow poppet of the Fusion Engine. comes with REV3 FCU
Polarstar F1 Mini FCU & Standard FCU
The F1 is a high performance, universal HPA drop-in cylinder. Comes with REV3 FCU (led screen & joystik) or mini FCU (programmation with trigger)
Polarstar Jack Mini FCU & Standard FCU
lthough economically priced, JACK™ still retains the same performance and quality you have come to expect from PolarStar products. Comes with REV3 FCU (led screen & joystik) or mini FCU (programmation with trigger)
Wolverine Inferno Premium / Spartan / Bluetooth
The GEN 2 Inferno features a revolutionary single solenoid, independent poppet and nozzle design that sets a new standard for a drop in kit. The GEN 2 Inferno is a HYBRID of Open Bolt and Closed Bolt technology. It takes the advantages of Open Bolt, but takes out the hassle of tuning and searching for the right hop up/bucking/barrel combinations.. Premium version comes with FCU in the stock tube, Spartan comes with FCU in the gearbox (programmation with trigger), Bluetooth comes with FCU in the stock tube & programmable with Android.
Wolverine Reaper Premium / Spartan / Bluetooth / Electro Mecanic
The Reaper is a new HPA airsoft system from Wolverine that features a true "closed bolt" firing system. The air is locked and loaded for its first shot, ready to go. Premium version comes with FCU in the stock tube, Spartan comes with FCU in the gearbox (programmation with trigger), Bluetooth comes with FCU in the stock tube & programmable with Android, Electro Mecanic comes without FCU and is semi-auto only
Polarstar Fusion Engine
the patented Fusion Engine is one of the most reliable, high performance airsoft systems available today. No matter if you need a high fire rate CQB setup or a high velocity sniper platform, the Fusion Engine can do it all without sacrificing dependability or trigger response. Comes with REV3 FCU (led screen & joystik). Please note that the Fusion Engine is not compatible with ambidextrous selector set, in the case you choose an AEG with ambidextrous selector you will get only the selector left side working, and sometimes we should be able to replace the original left selector to a CNC balystik.
Polarstar Fusion Engine + poppet mod
This modification allow to modify the original Fusion Engine to the range of power used mostly in european countries & reduce by 30 % the air consumption, also overall performances are improved. Min Power is 340 FPS & Max power is 430 FPS @ 120 PSI. FPS may change with inner barrel lenght and inner diameter. We have The lowered Original Poppet air flow by 75% and turn the original Nozzle in red Nozzle (4mm inner diameter) with our turning lathe. Please note that the Fusion Engine is not compatible with ambidextrous selector set, in the case you choose an AEG with ambidextrous selector you will get only the selector left side working, and sometimes we should be able to replace the original left selector to a CNC balystik.
No reviews at this time.
This service include all the the following task done in our workshop.
- Unmount of the original airsoft gun
- Modification (if needed) of the original gun to fit the new HPA system
- Modification (if needed) of the HPA nozzle to match perfectly with the original AEG nozzle outside length
- Installation of the HPA engine
- Installation of the motor grip plate connect (US or EU), if you don't purchase any regulator with the gun just let us know wich one you want. available on all models exept M249 A&K.
- FCU optimal programmation
- Unmount, cleanning & improvement of the hop-up unit
- Firing tests (around 500-600 BBs) to check about the working and grouping.
- Test of the regulator and the tank if purchased
- Additionnal engravings if you need !
- 1 year warranty
No reviews at this time.
CNC Aluminum Hopup Chamber ME Sport is precisely made to improve accuracy and ensure consistent air seal for Tokyo Marui (include KRYTAC and KWA) M4/M16 Standard AEG series. The Hopup Chamber ME unit has a precision rotary dial design for fine hopup adjustments, also re-engineered the hopup levers and concave nubs to work best with R-hop, Flat-Hop and Standard-Hop to keep the BBs shooting straight and accurate on every single shot. The Hopup Chamber ME unit is designed to accept the nozzle length from 21.00mm to 21.25mm, and fully compatible with most aftermarket soft and hard rubber bucking without losing FPS or dropping BBs. The Hopup Chamber ME Housing is equipped with a new CNC Delrin Locking C-Clip design to hold barrel tight without wobbling and twisting, and 3 compression springs on top, at bottom and in center of housing to ensure the hopup unit is exactly centered, straight and air tight at all times when adapted to any V2 gear boxes with 11mm or 11.5mm inner bore. More than that, the Hopup Chamber ME Sport unit is specially designed with BB Catching System to prevent dropping BBs after removing the magazine.
***The UV LED Tracer and Electronic Module are optional add-ons to glow BBs in the dark. Operating Voltage from 7VDC - 15VDC (2-4 cells LiPo, 6-13 cells NiCad). (Sold separately)
***The Empty Magazine Detection Sensor and Electronic Switch Controller are optional add-ons to stop Motor/HPA firing when the magazine is empty. (Sold separately)
***Test results: FPS might be increased from 10FPS to 30FPS over stock setup. Please check your FPS!
|1 x CNC Aluminum Hopup Chamber ME Sport|
|2 x Strong Clear Vinyl Cover set|
|1 x CNC Aluminum Standard-Hop Arm|
|1 x CNC Aluminum R-Hop Arm|
|1 x Silicone Rubber Standard-Hop Nub Damper|
|1 x Silicone Rubber R-Hop Nub Damper|
|1 x CNC Aluminum 4.5mm length Precision R-Hop Concave Nub|
|1 x CNC Aluminum 6mm length Precision R-Hop Concave Nub|
|1 x CNC Brass Threaded Slot Pin|
|1 x CNC Delrin Locking C-Clip|
|1 x CNC Barrel Brass Spacer|
|1 x Brass Spacer Holder Oring|
|3 x Steel Compression Spring|
|Overall Length: 51mm|
|Overall Height: 37.75mm|
|Hub Outer Diameter (to fit into Gear Box): min 11mm - max 11.5mm|
|Hub Outer Diameter (to fit into Outer Barrel): min 12mm|
|Hub Inner Diameter (to fit Nozzle): max 8.3mm|
|Feeder Outer Diameter (to fit magazine): min 9.25mm|
|Feeder Length (to fit magazine): max 6.25mm|
|Material: Aluminum 6061|
|Machined from a solid aircraft aluminum block with tight tolerances to provide better accuracy, consistency, and durability|
|Improved accuracy and ensure consistent air seal for Tokyo Marui (include KRYTAC and KWA) M4/M16 Standard AEG series|
|Precision rotary dial design for fine hopup adjustments|
|Re-engineered the hopup levers and concave nubs to work best with R-hop, Flat-Hop and Standard-Hop to keep the BBs shooting straight and accurate on every single shot|
|Removable Brass Threaded Slot Pin for setup and maintenance|
|Accepted the nozzle length from 21.00mm to 21.25mm|
|Fully compatible with most aftermarket soft and hard rubber bucking without losing FPS or dropping BBs|
|Equipped with a new CNC Delrin Locking C-Clip design to hold barrel tight without wobbling and twisting|
|Equipped with 3 compression springs on top, at bottom and in center of housing to ensure the hopup unit is exactly centered, straight and air tight|
|Compatible with any V2 gear boxes with 11mm or 11.5mm bore|
|Specially designed with BB Catching System to prevent dropping BBs after removing the magazine|
|The UV LED Tracer and Electronic Module to glow BBs in the dark ready!|
|The Empty Magazine Detection Sensor to stop Motor/HPA firing ready!|
|Compatible with most Tokyo Marui (include KRYTAC and KWA) M4/M16 standard AEG version 2 gearbox|
|Wearing eye protection is recommended|
|Use proper tools for disassembly and reassembly the gear box with great care due to spring tension|
|Bearing lubricant oil/grease is recommended for smooth operation|
|Instruction Manuals are included|
No reviews at this time.
R-hop provide an enhanced contact surface on the BB that creates a much more balanced backspin on the BB. Traditional hop-up rubbers have a small contact patch with the BB which does not deliver an effective backspin all the time. Some hop-up rubbers have two small contact patches to provide a more balanced spin, but that still does not provide a sufficiently large enough area for consistent spin. R-hops are essentially a semi-circular piece of rubber that covers 70% of the BB's upper hemisphere, providing a huge contact patch for much better backspin. Depending on the applicatoin, this can generate 5m- 25m of additional distance.
Package include :
The Prometheus Barrel showed in the picture is for demo only and not included.
Important NOTE : Silent Sniper Bucking R-HOP is only compatible with old system Prometheus EG barrels
No reviews at this time.
We shorten at the max the trigger course byinserting a screw on the gearbox shell. P6 adjustable trigger mod gives the possibility to reduce the original trigger course close to the maximum for high speed response. The safety fonction is also modified to let the trigger close to the swich while keeping the safe mode fonctionnal.
Modification is made on the original trigger, you keep the possibility to add a spare CNC trigger in your order, we will take this last one to make the mod.
Not compatible with MAXX Model and G&G trigger
What is ICFU System ?
The ICFU System (Integrated Custom Firestop Upgrade) is a device which allows to stop firing when there is no BB left in the magazine. The ICFU system can be fitted on a M4, 416 or Scar-L airsoft gun equipped with a fusion engine (new feature) or drop-in HPA System type (exept N7 MILSIM) and requires specific 120 rounds magazines (originally PTS but modified).
Players buying a brand new complete HPA gun get 75% discount on the price, because the gun is already unmounted to install the HPA system and of course it is cheaper to make the mod rather than unmount & mount everything just for that. Only remain ICFU modification fees such as milling the gearbox shells, wiring, components and tests.
ATTENTION: Classic M4 AEG magazines will no longer be compatible when the system is fitted and could cause damage to the sysytem if inserted on the lower receiver.
No reviews at this time.
Choose your regulator (include regulator and line)
Choose your HPA tank
|PI approved regulator||yes|
|PI approved tank||yes|
Choose the battery model for your FCU.
This option is only available in our packs and cannot be bought separately.