Full metal, mosfet, ETU, skeleton body lightened for speed
The most important evolution of the new generation 2 Proline is undoubtedly the original addition of an electronic ETU trigger and a protection mosfet. This relaxation allows increased reactivity, a sensitivity of the relaxation stroke finer, battery voltage protection lo, gearbox rings collar, a pre-compression of the spring for a shooting start much faster, etc ... a small revolution, always affordable.
|Thread type||14mm CCW|
|Firing mode||Semi + Full automatic|
|Inner Barrel dia (mm)||6.03|
|Gearbox inserts||8mm Bushings|
|Gear ratio||18:1 Torque|
|Quick change spring||Yes|
|Integrated Mosfet||Yes Factory built in|
|Motor||V2 Long Axis|
|Magazine Version||Mid-cap Spring operated|
|Battery charger||Not Included|
|Battery Connector||Small Tamiya|
|Power (FPS @ 0.20gr)||370|
Have you ever dreamed of Polarizing your MP5, G3 or SCAR? With the introduction of the GEN3, now you can! At first glance the GEN3 FE looks very much like the GEN2 and, for the most part, the two are quite similar. However, unlike its predecessor, the FE GEN3 is no longer just for the M4/M16 series rifle. We applied the same concept used with our Version 3 Fusion Engine™ so that it is now able to interface with the selector plate and related components of your existing AEG’s gearbox.
The FE GEN3 will come complete with a trigger and steel selector plate so that it can be installed into any airsoft gun which is Tokyo Marui compatible. However, by installing a different nozzle or rifle specific conversion kit, you will be able to expand the number of rifles it will be compatible with. In most cases all you’ll need to do is change out the trigger and selector components with ones from your AEG, install a different Fusion Engine™ nozzle, and the engine is ready to use in a completely different model of rifle.
The internal operation of the Fusion Engine cylinder assembly are exactly the same and share many of the same parts, so it offers the same stellar downrange performance and rock solid reliability as its predecessor. This GEN3 does however feature a new side plate design to accommodate the AEG selector plate and is equipped with a new electronic switchboard. One advantage to this new design is that the switchboard offers a wider contact point with the selector plate to allow for varying tolerances in the rifles selector assembly making for improved out-of-the-box compatibility with an increased number of rifle brands.
As requested by many of our fans, the FE GEN3 will come standard with our newly redesigned “Milsim Manifold”. This feature enables the user to install an optional 90 degree fitting inside of their engine allowing the air line to be routed to the rear of the engine and exit through the buffer tube sling plate on an M4 series rifle.
As with all of our engine models, you can quickly change and adjust key functions of the engine via the on-board FCU (Fire Control Unit) which is no bigger than an AEG`s MOSFET and can easily fit inside of a rifles battery compartment along with a small Li-po battery. Using the FCU`s five position joystick and LCD display you will be able to easily adjust such functions as the systems cyclic rate, fire modes and nozzle timing on the fly.
With the Fusion Engine™ in your rifle you will also be able to adjust its muzzle velocity via the remote air rig (sold separately). Adjusting the PSI output on your air rig will allow you to fine tune your rifles muzzle velocity so you will always be able to get it exactly where you want it. And then for larger velocity changes we offer a series of air nozzles with varying bore sizes to shift the velocity adjustment range up or down to best meet your requirements.
The best part is that our system is extremely user friendly. Even if you have only the basic understanding of an airsoft rifle, you will find that operating and manipulating this system is very simple and does not require a degree in airsoft engineering to figure out.
Fire mode/s : Full Auto, Semi Auto, Variable Burst
FE Profile: M4
Included Selector Plate: M4/M16 Series
Cyclic Rate: 500 RPM to 1,800 RPM
Fire Modes: Semi / 2 to 9 Shot Burst, Semi / Full Auto, Semi Only
Power Source: HPA (High Pressure Air via remote air rig)
FCU Battery: 7.4v Lipo w/ JST Connector
FCU Voltage Input Range: 6.8v to 12v
PSI Operating Range: 80 psi. to 120 psi.
Build Material: Aluminum
Please note that instaling a HPA drop in system is recommanded for skilled gunsmith only. The product comes as a spare part and does not come with installation manual. By purchasing an HPA system you take entire responsability of the assembly and upcoming results. For products delivered with a trigger board, contactors / switch are not guaranted by the manufacturer in case of break. We advice to take extreme care when installing the selector plate in order to not break the button. Regarding the trigger switch, it is recommended to block mecanicaly the trigger once the the trigger switch is activated to avoid excessive pressure on it.
|HPA System||Polarstar Fusion Engine|
|HPA Fitting type||6mm hose|
The Polarstar Fusion Engine poppet is designed to work with all the powers offered by the wide range of nozzles, the original air flow is therefore very high and not optimized for low powers (large air release on poppet side and tiny nozzle diameter). Our preparation carried out in the workshop aims to modify the poppet by reducing the air flow released instantly by the valve and by enlarging the internal diameter of the original nozzle.The poppet air flow modification have only one single hole (unlike the red and yellow Polarstar sprinkler type poppets) and it is identical to the inner diameter of the modified nozzle, which optimizes air flow and air consumption for the requested power. Maximum power at 120 PSI is around 430FPS. FPS results may vary depending on the length and diameter of the barrel.
P6 poppet & nozzle mod include :
FPS may change with inner barrel lenght and inner diameter
This service include all the the following task done in our workshop.
- Unmount of the original airsoft gun
- Modification (if needed) of the original gun to fit the new HPA system
- Modification (if needed) of the HPA nozzle to match perfectly with the original AEG nozzle outside length
- Installation of the HPA engine
- Installation of the motor grip plate connect (US or EU), if you don't purchase any regulator with the gun just let us know wich one you want. available on all models exept M249 A&K.
- FCU optimal programmation
- Unmount, cleanning & improvement of the hop-up unit
- Firing tests (around 500-600 BBs) to check about the working and grouping.
- Test of the regulator and the tank if purchased
- Additionnal engravings if you need !
- 1 year warranty
What is ICFU System ?
The ICFU System (Integrated Custom Firestop Upgrade) is a device which allows to stop firing when there is no BB left in the magazine. The ICFU system can be fitted on a M4, 416 or Scar-L airsoft gun equipped with a fusion engine (new feature) or drop-in HPA System type (exept N7 MILSIM) and requires specific 120 rounds magazines (originally PTS but modified).
Players buying a brand new complete HPA gun get 75% discount on the price, because the gun is already unmounted to install the HPA system and of course it is cheaper to make the mod rather than unmount & mount everything just for that. Only remain ICFU modification fees such as milling the gearbox shells, wiring, components and tests.
ATTENTION: Classic M4 AEG magazines will no longer be compatible when the system is fitted and could cause damage to the sysytem if inserted on the lower receiver.