Panier
Il y a 8013 avis.
Seuls les clients enregistrés peuvent poster un avis.
Connectez-vous ou créez un compte
.
11/03/2024
Tom L.
verified_user Achat Vérifié
formidable
magnifique qualité, polyvalent, stable/sans jeu
c'est un budget, mais il permet beaucoup de chose en plus d'ajouter un visuel à la réplique
10/03/2024
Geoffrey L.
Puissant
Trop puissant monte dans un hk416 full upgrade short stroker de deux dents ça tape encore à 430-440 fps donc non short stroké avec une étanchéité parfaite cela monte facile à 460-470 fps
10/03/2024
Clément l.
Pas parfait
Contrairement à ce qui est marqué dans l’annonce c’est 2 charbons et non 1 qui sont vendus.
Ensuite la pièce présente un défaut de conception car la courbure sur le charbon sensé épouser le rotor moteur se retrouve horizontale et non verticale limitant la surface de contact.
Pour une réplique sans mosfet pas de problèmes ca se rodera facilement, mais avec mosfet comme le scorpion evo la réplique se bloque sans arrêt en sécurité et rends le rodage très compliqué.
10/03/2024
Morgane A.
une catastrophe
j'avais 400 fps avec mon bloc d'origine à 2 Euros, maintenant avec ce bloc ça sort 230 fps... 70 boules pour une perte pareille c'est inadmissible. bloc très douteux ...
10/03/2024
Andy p.
verified_user Achat Vérifié
Supris de la qualité
Tre solide je pense avoir du plastique moue mais tre solide à voir dans le tenps
09/03/2024
Patryk B.
Patryk B
At the beggining i had to seal the whole thing because it was leaking gas - the plastic tube between gas chamber and top of mag is huge weakspot here. Top of mag is connected with 4 screws in plastic, kinda weak, but it's possible to to use diffrent screw with nut on other side, kinda sad it's not made like that out of box. Much better gas effeciency than with double eagle magazines, much more consistent fps, but in my case fragment of gas route tore off after something like 800 shots.
Winding the spring with hex key, not very practical but it's possible to shoot soomething like 200-250 shots before you have to use hex key again.
09/03/2024
adrian c.
verified_user Achat Vérifié
Meinung
hat mich nich bei der Montage nicht überzeugt. auf das Kunststoff Gewinde hält es nicht bomben fest dreht sich leicht mit.
Optisch top
09/03/2024
adrian c.
verified_user Achat Vérifié
Meinung
Gut gefertigter ladehebel passt perfekt auf die AAP-01 , kein nachbearbeiten nötig.
09/03/2024
adrian c.
verified_user Achat Vérifié
Meinung
Kosten günstiger Hpa Adapter , einfache Montage altes Ventil raus drehen und das neue rein und Fertig , dichtet super ab,
09/03/2024
adrian c.
verified_user Achat Vérifié
Meinung
Hochwertiger Lauf von PDI hervorragende Qualität zu gutem Preis.
09/03/2024
adrian c.
verified_user Achat Vérifié
Meinung
Nach meiner Meinung die besten BB`s auf dem Markt. gleichbleibende gute bb`s.
08/03/2024
Urbino N.
verified_user Achat Vérifié
Ilha da Madeira
resposta muito positiva, excelente equipa.
07/03/2024
Nicolas L.
verified_user Achat Vérifié
Nikel,top dans le délai,
07/03/2024
Adrie E.
verified_user Achat Vérifié
Dmr
Top winkel product snel in huis als ik nog iets nodig heb ga ik het zeker bij hun kopen
06/03/2024
Babut H.
Dimentions
Hollo. I saw in the comments that it is compatible with VFC HK416 A5 GBB. According to mil-spec, inner dimention of stock should be 1.15 inch or 2.92 cm. Can you confirm, please? I bought one magpul stock, mil-spec mention on the box, and inside was 1.17 inch, the commercial dimention. This purchase it was not from you! Because you are top, I just want to be sure that if it is mil-spec, it really have 1.15 inch inner diameter. Can you please help?