> >>P6 Workshop MP7 VFC HPA Polarstar F2
New P6 Workshop MP7 VFC HPA Polarstar F2 View larger
Previous Next

P6 Workshop MP7 VFC HPA Polarstar F2

P6-2.6393X-F2

New product

Time to produce : 3 -5 days

Moyenne des votes pour ce produit
0 / 5
Moyenne : 0 / 5
Basée sur 0 avis clients.

1 249,92 € tax excl.

Customize your product

Quantité totale 0

Vous ne pouvez pas ajouter plus de 5 quantité(s)

  • UMAREX VFC MP7A1 GEN2 H&K AEG

    This is the NEW GEN2 version with fixed issue by the manufacturer, including the new tappet plate and decocking button on the top of rail. The long awaited Umarex MP7 AEG is finally here and is a full sized and accurate representation of the wildly popular SMG from Heckler and Koch. Being a fully licensed product it features all the corresponding markings and trades. The MP7 AEG comes with a few features that do make it stand out as a unique product in its own right. Aesthetically, the gun features a full CNC steel flash hider and the high quality polymer build know from its GBBR counter part. Internally the gun features a new, next generation micro switch and FET system. Additionally, the gun features empty magazine detection giving the AEG an extra level of realism.

    Features :

    • Steel CNC MP7 flash hider
    • Full ambidextrous controls
    • Next generation micro fire control and FET
    • Empty magazine detection
    • 110 round magazine capacity
    • Side rails not included

    Please not that it is imperative to run this replica with 7.4v battery, higher voltage may damage the gearbox.

    Important note regarding magazine : There is a very important operating tip please users notice carefully. The MP7 AEG magazine comes with a new swing-able follower, which could fits bullets tunnel much freely that we can make more capacities in the MP7 AEG mags. However the new follower will goes out from magazine once the ammos ran dry, if you need to insert the empty mag into receiver for some reasons (storage, photo taking...etc.), Please remember PUSH DOWN THE FOLLOWER FIRST, because the follower tip may tilt to side and bump your hop-up port, Please check it's locked inside mag by retainer before insert.

    UMAREX VFC MP7A1 GEN2 H&K AEG

  • Maple Leaf MR Hop Up Rubber for AEG - 60 Degree

    Maple Leaf l MR "Maximum Range" rubber is designed to improve the performance and the range of your airsoft replica.

    • For AEG airsoft barrel
    • Larger & wider contact patch for better hop effect with heavy BB's
    • The design in the shape like a "shield" ensures better support of the hop up with the support levers
    • The shield-shaped groove design has a better jump effect when the tensioner / lever presses it

    Product include 1X Maple Leaf MR Hop Up Rubber for AEG - 60 Degree (yellow)

    Maple Leaf MR Hop Up Rubber for AEG - 60 Degree

  • Polarstar Universal Plugboard

    The Universal Plugboard is used in all of our MG series kits such as the M249 and is used across all of our systems including the Fusion Engine. It is also useful for custom wiring when a model specific switchboard is not available.  There are four 2-pin headers and one 5-pin header on the plugboard.

    The 5-pin is for the main wiring harness. The 2-pin headers are labeled CON1 through CON4

    Polarstar Universal Plugboard

  • F2 aluminium nozzle for MP7 VFC

    F2 aluminium nozzle for MP7 VFC

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • PolarStar F2 M4 with T238 meteor FCU

    Polarstar F2 M4 comes with the T238 Meteor FCU as a replacement for the original Polarstar FCU, wires are plug and play, no soldering required for connecting Meteor to the trigger board.

    Product content :

    • Polarstar F2 V2 M4
    • Polarstar FCU wire harness    
    • T238 FCU Meteor
    • Polarstar V2 Trigger board    
    • English Manual

    METEOR is a programmable FCU designed specifically for HPA engines, supporting single-valve and double-valve engines, integrating power connector for gel ball magazines, and power connector for tracer Hop-ups. METEOR can simultaneously save the configuration parameters of three different engines, and can freely switch between the three sets of configuration parameters. It supports voltage input of 6~12.6V, making the power more abundant.

    Compatibility:

    • The METEOR FCU is directly compatible with Polarstar F1/F2 and Fusion Engine systems without soldering, making it plug and play.
    • For Wolverine and Pulsar Gate systems, you simply need to add a T238 trigger board for perfect compatibility, requiring no soldering and making it plug and    play.

    Functions:

    1. METEOR supports 3 sets of FCU configurations, FCU1, FCU2, and FCU3. You can choose which FCU configuration to run in the CHOOSE FCU option.
    2. Supports open bolt and closed bolt. When using a double-valve engine, open or closed bolts can be selected through CB mode.
    3. Auto-loading function is designed for gel ball blaster magazines with a motor inside, when changing the magazine, the magazine motor will run automatically for a few seconds.
    4. Paintball mode. When the trigger frequency is low, the engine will fire a single shot; when the trigger frequency is high, the engine will continue to fire continuously.
    5. Sniper mode. After activating sniper mode, both semi-auto and full-auto modes execute single-shot shooting, and can only fire once within the set period. When sniper mode is activated, paintball mode is no longer effective.
    6. Low battery protection, the system automatically sets the protection voltage based on the battery type. If the system detects that the battery voltage is lower than the protection voltage, it will automatically shut down.
    7. Auto shutdown. If the device is not operated within the set time, such as pulling the trigger, loading the magazine, or pressing the settings button, the system will automatically shut down and enter sleep mode.
    8. Friction control. This parameter is used to compensate for power after the engine is left idle for some time.
    9. BB limit. This function is a virtual number of BB/gel ball setting, where VALUE is the limit of BB/gel ball number. When the number of shots reaches the limit, the system will wait for 2 seconds and cannot fire during this waiting period.

    Features:

    • Size: 60*23*10mm
    • JST connector for battery, JST ZH 5Pin for trigger board
    • Supports input voltage of 6~12.6V
    • Supports single-valve or double-valve engines
    • Integrated magazine power supply interface and auto pre-loading function for gel ball blasters
    • Simultaneously save 3 sets of different engine configuration parameters
    • Compatible with Polarstar V2/V3, Blackleaf Speed GEN2 trigger boards

    Package Content:

    • FCU METEOR x1
    • Manual x1
    • Badge x1
    • JST ZH1.5-5P*20CM x1
    • JST ZH1.5-3P*20CM x1

    Shooting Modes:

    • SAFE: This model is completely the same as the original safe model. The trigger is stopped by the safety lever.
    • SEMI: This model can be programmed to implement semi-auto, binary trigger, 3 rounds burst to 9 rounds burst, the default model is semi-auto.
    0,00 €
    PolarStar F2 M4 with T238 meteor FCU

    0,00 €

  • PolarStar F2 M4

    Product content :

    - Polarstar F2 V2 M4
    - FCU wire harness    
    - FCU REV3    
    - V2 Trigger board    
    - English Manual

    What is F2?

    F2 is essentially a Mini Fusion Engine. It offers the same adjustability and performance as the Fusion Engine in a cylinder sized package.

    Patented Dual Solenoid Design

    The dual solenoid design of the F2™ provides the same functionality as the legendary Fusion Engine™ but in a more compact, efficient and flexible design. Dual solenoids allow for the nozzle and the poppet valve to be adjusted independently of each other for unparalleled control over both the loading time and air volume used. Additionally, this makes it possible to change the firing sequence giving it the ability to operate in both true closed bolt as well as "AEG" mode.

    Increased Efficiency

    The F2™ incorporates a new one-piece, lightweight poppet valve design yet still operates on the same principle as the Fusion Engine™ poppet. This valve is able to operate at lower pressures and uses less air volume to function which optimizes air efficiency. The standard F2 poppet is equivilent to the Red Low-Flow poppet of the Fusion Engine.

    Spring Loaded Nozzle

    The F2™ nozzle is spring biased forward which provides a consistent loading force regardless of operating pressure. It shares the same spring as the Fusion Engine™ with both light and heavy spring options available to adjust the loading force. The robust design of the F2™ allows for an operating pressure range of 45psi to 145psi which enables it to achieve velocities from CQB to DMR while employing only one nozzle for the entire velocity adjustment range.

    What is the difference between F2, F1 and JACK ?

    Both F1 and JACK are "open bolt" systems, meaning the nozzle is in the rearward position when the system is idle and the round is fired during the forward movement of the nozzle. F2 is a dual-solenoid system which allows for complete control over the shot cycle

    Nozzles :

    Over 20 standard F2 nozzles are available for installation into a wide range of replicas. These are numbered, rather than named, since a single nozzle is often compatible with multiple replicas. The "Original Model" listed in the table is the replica from which the nozzle measurements were taken and is for reference. If your gun is not listed in our Compatiblity Database a recommended nozzle length may calculated by measuring your original gearbox and applying the following formula: TIP = F + B - (A/2) - .057. A more precise measurement (which accounts for the hopup and bucking in use) may be obtained by installing a nozzle into the system which is slightly too long for the replica and measuring the nozzle setback when placed into the hopup.

    Options available in the future :

        Offset and Centerline cylinders and nozzles.
        Wire harnesses are available in 7.5", 13" and 18" standard lengths
        Interchangable Bushing Inserts which prevent any movement of F2 within the gearbox.
        Custom nozzle lengths available.
        Low velocity poppets (< 1J) available.
        Light and Heavy nozzle springs available.

    Please note that instaling a HPA drop in system is recommanded for skilled gunsmith only. The product comes as a spare part and does not come with installation manual. By purchasing an HPA system you take entire responsability of the assembly and upcoming results. For products delivered with a trigger board, contactors / switch are not guaranted by the manufacturer in case of break. We advice to take extreme care when installing the selector plate in order to not break the button. Regarding the trigger switch, it is recommended to block mecanicaly the trigger once the the trigger switch is activated to avoid excessive pressure on it.

    16,67 €
    PolarStar F2 M4

    16,67 €

Choose your color and your US or EU connector type

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

Vous devez ajouter un minimum de 1 quantité(s)

  • Balystik braided line for HPA replica - Black US

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • US Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Black US

  • Balystik braided line for HPA replica - Tan US

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • US Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Tan US

  • Balystik braided line for HPA replica - Red US

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • US Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Red US

  • Balystik braided line for HPA replica - Grey US

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • US Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Grey US

  • Balystik braided line for HPA replica - Deep coffee US

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • US Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Deep coffee US

  • Balystik braided line for HPA replica - OD US

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • US Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - OD US

  • Balystik braided line for HPA replica - Black EU

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and an additional finishing touch for your replica, ideal for supplying your replica with air in a high-performance and leak-free way during your airsoft games !

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • EU Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Black EU

  • Balystik braided line for HPA replica - Deep coffee EU

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • EU Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Deep coffee EU

  • Balystik braided line for HPA replica - Grey EU

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • EU Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Grey EU

  • Balystik braided line for HPA replica - Red EU

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • EU Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Red EU

  • Balystik braided line for HPA replica - Tan EU

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • EU Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - Tan EU

  • Balystik braided line for HPA replica - OD EU

    The Balystik braided HPA line is an original solution for replacing the original macro line of the HPA replicas. Easy to install, it is specially designed to be clipped directly behind your HPA drop-in system and exit under your pistol grip. Thanks to its integrated elbow, it allows direct alignment in the direction of the grip and avoid risk of bending. The braided finish offers much better resistance and additional touch of style for your HPA gun.

    • HPA system compatibility : most of drop-in system such as Wolverine Inferno & reaper , Polarstar F2, F1, jack.
    • Replica compatibility : most of replicas with V2 gearbox : M4, Scar, 416, MP5 ....
    • Not compatible with Fusion engine and MTW
    • EU Connector version

    91967.jpg?time=1673513102207

    Balystik braided line for HPA replica - OD EU

20% Discount

Qiantité totale 0

Vous pouvez ajouter un maximum de 50 quantités

  • Umarex VFC 120rds Magazine for MP7A1 aeg

    The Umarex MP7A1 New Generation AEG 110rds Magazine is designed to work specifically with the Umarex MP7A1 AEG.

    Important note regarding magazine : There is a very important operating tip please users notice carefully. The MP7 AEG magazine comes with a new swing-able follower, which could fits bullets tunnel much freely that we can make more capacities in the MP7 AEG mags. However the new follower will goes out from magazine once the ammos ran dry, if you need to insert the empty mag into receiver for some reasons (storage, photo taking...etc.), Please remember PUSH DOWN THE FOLLOWER FIRST, because the follower tip may tilt to side and bump your hop-up port, Please check it's locked inside mag by retainer before insert.

    22,60 €
    Umarex VFC 120rds Magazine for MP7A1 aeg

    28,25 € 22,60 €

Remises par quantités

15% Discount

Qiantité totale 0

Vous pouvez ajouter un maximum de 100 quantités

  • ASG 7.4V 250mah 20C lipo battery for HPA

    This LI-PO battery is made for HPA powered Airsoft guns. Designed to be as small and compact as possible. It can easily be built in to pistol grips or stocks, where it powers the HPA FCU. Comes with with a JST Discharge plug. 
    5,60 €
    ASG 7.4V 250mah 20C lipo battery for HPA

    6,58 € 5,60 €

  • Gens ace 250mAh 7.4V 35C Lipo Battery - JST

    Gens ace 250mAh 7.4V 35C 2S1P HPA Lipo Battery with JST-SYP Plug is one of the top rank battery corporations with deep research and manufacturing on NIMH, LI-PO, LI-FE by the effort of 200 professional engineers and technicians with 20 years of exquisite battery technology. 

    •  Capacity: 250mAh
    •  Voltage: 7.4V/2S
    •  Discharge Rate: 35C
    •  Weight: 17g
    •  Size: 37*20*10mm

    Gens ace 250mAh 2S 35C battery is suitable for HPA Control.

    6,30 €
    Gens ace 250mAh 7.4V 35C Lipo Battery - JST

    7,42 € 6,30 €

  • VB Power 7.4v 300mah lipo battery for HPA

    Suitable for Wolverine & Polarstar FCUs

    6,30 €
    VB Power 7.4v 300mah lipo battery for HPA

    7,42 € 6,30 €

Remises par quantités

Quantité totale 0

Vous ne pouvez pas ajouter plus de 1 quantité(s)

  • Lambda 05 precision Barrel 6.05 for AEG / M14 208mm

    Precision barrel in SUS304 stainless steel compatible with AEG M4 and M14 replicas. These guns are directly manufactured in the Osaka factory in Japan and are of very high quality. All LAMBDA guns are designed on CNC machines.

    • The FIVE range from Lambda is the most precise range in terms of finish with its 1 micron tolerance.
    • The FIVE range from Lambda is similar to the high-end PDI.
    • The internal diameter is 6.05mm
    • The external diameter is 8.55mm

    canon-de-precision-lambda-five-pour-aeg-

    32,42 €
    Lambda 05 precision Barrel 6.05 for AEG / M14 208mm

    32,42 €

  • PDI 6.01 Precision Inner Barrel for AEG 205mm

    Airsoft may be just a game, but the engineers and machinists at PDI definitely don't play around. These barrels are cold-hammer forged, which is the same process that real firearm barrels undergo. This process creates a very consistent bore that gives the barrel a tolerance of +0.002mm. This tolerance is currently the highest quality in the entire Airsoft industry for accessible stainless steel barrels. Custom made or lapped stainless barrels can surpass the inner surface of PDI, but those barrels are extremely expensive and are generally not accessible to most consumers. The material is SUS304 Stainless Steel. This Steel is harder to cut than most barrels and has superior corrosion resistance. Additionally, PDI barrels are very well known for their straightness and quality control. This barrel is 6.01mm best suited for high FPS.

    • Material: Cold Hammer Forged SUS304 Stainless Steel
    • 6.01mm (+0.002mm tolerance)
    • Made in Japan

    40,75 €
    PDI 6.01 Precision Inner Barrel for AEG 205mm

    40,75 €

  • PDI 6.03 Precision Inner Barrel for AEG 208mm

    The 03 barrel has a tight inner diameter and is a model that emphasizes on FPS. It is a precision stainless steel barrel made by cold forging. Since the inner diameter is slightly wider than the 01 barrel, it is less likely to get jammed with sand, dust and wax compared to 01, and it requires less maintenance. However, do be sure to perform regular maintenance just in case.

    • Outer Diameter：8.55mm
    • Inner Diameter：6.03mm
    • Tolerance：±0.002mm
    • Material：SUS304

    41,58 €
    PDI 6.03 Precision Inner Barrel for AEG 208mm

    41,58 €

  • PDI 6.05 Precision Inner Barrel for AEG 205mm

    Airsoft may be just a game, but the engineers and machinists at PDI definitely don't play around. These barrels are cold-hammer forged, which is the same process that real firearm barrels undergo. This process creates a very consistent bore that gives the barrel a tolerance of +0.002mm. This tolerance is currently the highest quality in the entire Airsoft industry for accessible stainless steel barrels. Custom made or lapped stainless barrels can surpass the inner surface of PDI, but those barrels are extremely expensive and are generally not accessible to most consumers. The material is SUS304 Stainless Steel. This Steel is harder to cut than most barrels and has superior corrosion resistance. Additionally, PDI barrels are very well known for their straightness and quality control.

    This barrel is 6.05, which is the same diameter as standard AEG barrels. The 6.05 bore is best suited for long range engagements. Through their own research and testing, PDI has found that wider bores give better accuracy over longer distances than tighter bores.

    • Material: Cold Hammer Forged SUS304 Stainless Steel
    • 6.05mm (+0.002mm tolerance)
    • Made in Japan

    40,75 €
    PDI 6.05 Precision Inner Barrel for AEG 205mm

    40,75 €

  • PDI 6.08 Precision Inner Barrel for AEG 208mm

    Airsoft may be just a game, but the engineers and machinists at PDI definitely don't play around. These barrels are cold-hammer forged, which is the same process that real firearm barrels undergo. This process creates a very consistent bore that gives the barrel a tolerance of +0.002mm. This tolerance is currently the highest quality in the entire Airsoft industry for accessible stainless steel barrels. Custom made or lapped stainless barrels can surpass the inner surface of PDI, but those barrels are extremely expensive and are generally not accessible to most consumers. The material is SUS304 Stainless Steel. This Steel is harder to cut than most barrels and has superior corrosion resistance. Additionally, PDI barrels are very well known for their straightness and quality control. This barrel is 6.08, which is the same diameter as standard AEG barrels. The 6.08 bore is best suited for long range engagements. Through their own research and testing, PDI has found that wider bores give better accuracy over longer distances than tighter bores.

    - Material: Cold Hammer Forged SUS304 Stainless Steel
    - 6.08mm (+0.002mm tolerance)
    - Made in Japan

    41,58 €
    PDI 6.08 Precision Inner Barrel for AEG 208mm

    41,58 €

  • PDI 6.15 Precision Inner Barrel for AEG 208mm

    PDI’s 15 inner barrel with a loose 6.15 mm inner diameter. Although acuracy is increased, there is a high possibility that the initial speed will decrease. This barrel is suitable for indoor use and when you want to lower the initial speed compared to the normal barrel and to improve accuracy. Ideal for HPA system !

    • Outer Diameter：8.55mm
    • Inner Diameter：6.15mm
    • Tolerance：±0.002mm
    • Material：SUS304



    41,58 €
    PDI 6.15 Precision Inner Barrel for AEG 208mm

    41,58 €

  • PDI 6.01 Precision Inner Barrel for AEG 208mm

    Airsoft may be just a game, but the engineers and machinists at PDI definitely don't play around. These barrels are cold-hammer forged, which is the same process that real firearm barrels undergo. This process creates a very consistent bore that gives the barrel a tolerance of +0.002mm. This tolerance is currently the highest quality in the entire Airsoft industry for accessible stainless steel barrels. Custom made or lapped stainless barrels can surpass the inner surface of PDI, but those barrels are extremely expensive and are generally not accessible to most consumers. The material is SUS304 Stainless Steel. This Steel is harder to cut than most barrels and has superior corrosion resistance. Additionally, PDI barrels are very well known for their straightness and quality control. This barrel is 6.01mm best suited for high FPS.

    • Material: Cold Hammer Forged SUS304 Stainless Steel
    • 6.01mm (+0.002mm tolerance)
    • Made in Japan

    41,58 €
    PDI 6.01 Precision Inner Barrel for AEG 208mm

    41,58 €

  • PDI 6.10 Wide Bore Inner Barrel for AEG 208mm

    PDI 6.10mm High Precision Wide Bore Inner Barrel for AEG with a margin of 0.007mm per barrel. Wide bore barrels are known for pushing distance rather than power. Perfect for reaching targets without worrying about them reaching you. Material : carbon steel STKM-12C-EC

    24,92 €
    PDI 6.10 Wide Bore Inner Barrel for AEG 208mm

    24,92 €
Qiantité totale 0

Vous pouvez ajouter un maximum de 4 quantités

  • Cyma 7 slots picatinny rails for MP7 VFC

    • Metal alloy construction, screw included
    • 20mm picatinny rail
    • For Umarex MP7 AEG / GBB
    6,58 €
    Cyma 7 slots picatinny rails for MP7 VFC

    6,58 €

  • VFC MP7 Slide Rail Set for Umarex MP7A1

    18,25 €
    VFC MP7 Slide Rail Set for Umarex MP7A1

    18,25 €

  • Side Rail Set for VFC Umarex MP7A1

    Rail set for Umarex / VFC MP7A1

    • Compatible with Umarex MP7A1 AEG
    • Compatible with Umarex MP7A1 GBB
    • Polymer 3D made
    • Set of 2 rails
    • Comes with screw X4
    4,13 €
    Side Rail Set for VFC Umarex MP7A1

    8,25 € 4,13 €

  • XL Side Rail Set for VFC / Umarex MP7A1

    Rail set for Umarex / VFC MP7A1

    • Compatible with Umarex MP7A1 AEG
    • Compatible with Umarex MP7A1 GBB
    • Set of 2 rails
    • Comes with screw X4
    4,54 €
    XL Side Rail Set for VFC / Umarex MP7A1

    9,08 € 4,54 €

Remises par quantités

arrow_drop_downRécapitulatif :

Total :

Partagez votre création avec vos amis.

More info

The Powair6 workshop presents the MP7 VFC converted using the Polarstar F2 HPA system. This replica is an addictive concentration of maneuverability capable of emptying the magazine in just a few seconds. Particular attention has been paid to the hop-up adjustment with the addition of a two-screw TDC system that allows for precise trajectory adjustment. Replica include

  • MP7 VFC replica modified in our workshop (code 2.6393X)
  • Polarstar F2 with custom aluminum nozzle and T238 Meteor FCU
  • Polarstar universal trigger board
  • Mapple Leaf MR60 hop-up rubber
  • Optimized hop-up TDC system
  • Balystik braided line with connectors of your choice

Please note :

  • Original mecanical parts are not included with the package
  • Charging handle and bolt not fonctional due to HPA conversion

Customization

After saving your customized product, remember to add it to your cart.

loader

* required fields

Accessories

Airsoft gun Law

This airsoft replica is subject to the french Decree No. 99-240 of March 24, 1999, which regulates the law of replica firearms developing an output energy from the muzzle greater than 0.08 joule and equal to or less than 2 joules. This product is intended for recreational use only. By adding this product to your cart, you acknowledge:

  • Being older than 18
  • Master the basic safety rules concerning the use of this type of replica (wearing protective glasses, playing in a suitable and private place, etc.).
  • Never expose the replica in a public place because it can be mistaken for a real weapon with all the disastrous consequences that this implies
  • Being in full knowledge of the airsoft laws in your local country and buying knowingly, Powair6 cannot be responsible in the case of illegal importation.
  • Never point or shoot at a person, animal or any other object representing any danger.
  • Do not aim with your replica until you are ready to shoot at the target you have selected.
  • Do not shoot on a hard surface, risk of the ball bouncing, or in water, which could cause dangerous ricochets.
  • Do not aim the shot at the eyes or ears.
  • Do not use airsoft without wearing goggles or a protective mask.
  • Do not attempt to modify or disassemble the product in order to increase its firing power. It can be dangerous and will void the warranty.
  • Always be sure to keep the safety “ON” when you are no longer using the product.
  • Never look into the barrel, a BB may be hurt your eyes.

P6 Workshop

P6 Workshop

Our own Airsoft Workshop Brand based in Pechbonnieu France

See all products from P6 Workshop

Questions 

Pas de question client pour le moment.

Seuls les utilisateurs enregistrés peuvent poser une question. Login

Avis

Seuls les clients enregistrés peuvent poster un avis. Connectez-vous ou créez un compte .
Tri:

Aucun avis pour le moment.