HPA replica MTW HPA system HPA Magazine | Electronics Battery Nozzle Parts | Stock Grip Dropstock | Regulator Hose Fittings
| Air tanks
Air systems |
AEG Replica
P6 Custom | Magazine Hop-Up Precision barrel Complete upper Stand | Mosfet AEG spring Trigger Motor
| Gearbox
| Body and Parts
Dropstock | Kriss Vector Zone Scorpion Zone AEP Zone PTW Zone Skins |
Gas & Co2 airsoft pistol Gas & Co2 airsoft rifles HOLSTER | Magazine
Magazine accessory Stand | Precision barrel Hop-up
Conversion kit | Pistol parts
AAP-01 Universe | GBBR rifle parts
RIS for M4 GBB Sling mount MWS Universe | Grenade launcher 40mm Grenade Grenade |
Sniper replica Magazine | Spring Precision barrel Hop-up Barrel spacer | Piston Spring guide Cylinder set Cylinder head | Trigger group Flash hider Outer barrel Upper Sniper | Cocking Handle Stock Rail Skins | SILVERBACK
VSR10 universe AAC T10 universe STRIKER universe |
SHOTGUN | Shotgun shell | Parts | Shell holder | Tank |
Stock Supressors
RIS System
| Front grips Front Rail Scopes and red dots
| Mount & accessories Iron Sights Sling Swivel Flashlights & Lasers | Communication Flash hider Gas block Magazine accessory | Magwell AN PEQ Tracer device Chrony | Case Tools Shooting target Bipod |
Battery & related
| Gas CO2 Skins | BBs BB loader | Maintenance Paint Light Stick | Battery Smoke grenade |
Gloves Slings Bags | Combat vest Face protection Googgles Powerbank | Ghillie Kneepad Helmet for roleplay Magazine holder | Team Armband Shemaghs Clothing BELT | Knife Cap / Beanie HOLSTER Pouch | Survival GPS Patchs Other |
Si vous souhaitez enregistrer votre configuration, vous devez d'abord vous connecter.
ConnexionAB++ is an on-wire mosfet, channeling the power from the battery to the motor through a specialized high-power transistor, instead of delicate mechanical switches, increasing reliability and replica performance. It also enhances your replica by adding many new, useful features. Comes with an universal wiring, that can be used in any replica. Only few easy soldering joints are needed to install the mosfet.
Electronic burst – Change auto to an electronically controlled burst to save your ammo and increase realism!
Active brake - active brake stops the motor after each shot preventing spring compression or in case of replicas with a high rate of fire, overspin (double shot problem).
Precocking - Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, the piston will remain in the rear position after each shot with the spring already compressed, ensuring that the next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger while simultaneously holding the button on the unit. A shot will be fired, with no precocking and fully braked.
Rate of fire reduction - Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.
DMR mode - Introduces intervals between semiautomatic shots to comply with DMR rules on some fields.
Low battery voltage alarm - Dedicated for Li-Po and Li-Ion batteries. When the battery voltage fall to a dangerously low level, the user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.
Diagnostic system - Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.
Electronic fuse - Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery if a short circuit or blocked motor is detected.
Programming of all the settings is done solely by using a trigger and a button on the device, in an easily memorable and quick sequences. Programming is supported by sound signals and a multicolor LED diode. That allows changing the settings at any moment, in a matter of seconds, even under enemy fire.
Upgrade kit works without problems with any battery from 7V to 17V. It can also be used with most extreme setups, without any limitations as to the spring rating.
Perun was established in 2016 with the aim of designing and manufacturing MOSFET devices and other parts for AEGs. After years of designing and testing we offer you products that will work reliably even in most extreme situations and enhance the capabilities of your replicas. All of our design work and most of manufacturing is done in the European Union state of Poland. That allows us to reach our main goal - keep the highest quality possible. We are in constant contact with players, airsoft techs, shops and consult with them to ensure, that our products satisfy their needs.
bonjour , compatible brushless ? cordialement .
Bonjour;
oui il sera compatible.
Cordialement.
this mosfet work on g&g mosfet ?
Hello , It is precisely dedicated for Mosfet G&G ETU .
Best regards,